Epoxy Resin and Epoxy Hardener Systems
Epoxy Products
Since 1980 we have added hundreds of products. You can find a complete listing of these products at
www.epoxy.com/products.aspx.
Need some help to find the right product for your job, give out Technical Support Department a call at 352-533-2167.
Our Technical Support Department can help you with the selection,
specification, installation, and maintenance of our products.
For a complete listing of all Our Products see
www.epoxy.com/products.aspx.
Product #1 All Purpose Coating is a 100% solids epoxy Hi-Build epoxy
resin and epoxy hardener coating system is used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, etc. Available in normal, fast, and Cold Temperature Cure versions.
Zero (0) VOC Epoxy Resin and Epoxy Hardener Coating (sometimes called epoxy
resin paint). Meets the lowest Federal and State Low VOC requirements.
This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Epoxy: Product #1 Fast - is a shorter potlife, and faster setting version of
Product #1,
This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Epoxy: Product #1 Cold Temperature Cure
Epoxy Coating is a version of
Product #1 Epoxy
Resin with a cold temperature Epoxy Hardener that sets even faster than Product#1 Fast
Epoxy Coating. Product #1 Cold Temperature Cure
Epoxy Coating is used in colder temperatures, or where an very fast cure is required.
This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Epoxy: Product #1W is a two component, 100% solids epoxy
hi-Build resin and epoxy hardener coating system used for high indoor traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, tanks, etc.
Zero (0) VOC Epoxy Coating (sometimes called epoxy paint).
Meets the lowest Federal and State Low VOC requirements.
This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Epoxy: Product #2 Chemical Resistant Coating is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. Available in normal, fast, and Cold Temperature Cure.
Zero (0) VOC Epoxy Resin Coating (sometimes called epoxy resin paint).
Meets the lowest Federal and State Low VOC requirements.
This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Epoxy: Product #2 Fast is a shorter potlife, and faster setting version of Product #2.
Uses a fast cure epoxy hardener. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Epoxy: Product #2 Cold Temperature Cure is a version of that sets even faster than Epoxy.com Product#2 Fast Cure. Typically used in colder temperatures, or where an very fast cure is required.
Uses a cold (winter) temperature epoxy hardener (cure). This
epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Product #2W Chemical Resistant Wall Coating is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications.
This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Product #5 Fast Set Gel
Epoxy Adhesive Resin System is a 100% solids high-mod epoxy
resin gel adhesive used for vertical and overhead bonding applications and
structural repairs. Product #5 Fast Set Epoxy Resin Gel Adhesive is also used as a grout for anchor bolts, dowels and rebar.
Zero (0) VOC Epoxy Adhesive (sometimes called epoxy resin glue, epoxy
resin bonder or epoxy resin bonding agent). Meets the lowest Federal and State
Low VOC requirements. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Epoxy.com Product#6 Gel - Normal Setting
Epoxy Adhesive is a high-mod epoxy resin and epoxy
hardener gel adhesive used for vertical and overhead bonding applications and structural repairs. It is also used as a grout for anchor bolts, dowels and rebar.
Zero (0) VOC Epoxy Adhesive (sometimes called epoxy resin glue, epoxy
resin bonder or epoxy resin bonding agent). Meets the lowest Federal and State
Low VOC requirements. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Product #6SC Long Pot life Adhesive produces a non-sagging material that is ideal for repairs on vertical or overhead surfaces. PRODUCT #6SC meets or exceeds the requirements of ASTM - C881-87, Types I, II, and IV, Grade 3 Class "B" and "C".
Zero (0) VOC Epoxy Resin Adhesive (sometimes called epoxy glue, epoxy
resin bonder or epoxy resin bonding agent). Meets the lowest Federal and State
Low VOC requirements. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to
LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Product #7 All Purpose Epoxy Bonding Agent is a two component, 100% solids epoxy resin
and epoxy hardener system designed to bond new concrete to old and other materials to concrete. It has a convenient 1:1 mix ratio, by volume with a viscosity similar to heavyweight oil. It exceeds the requirements of ASTM C-881-90, Types I, II, IV and V, Grade 2, Class "B" and "C".
Zero (0) VOC wet Concrete to hardened Concrete Adhesive Epoxy Resin .
Meets the lowest Federal and State Low VOC requirements.
Product #7SC i is a 100% solids high-mod epoxy adhesive used to bond fresh concrete to cured concrete, steel to fresh or hardened concrete, as a grout for anchor bolts, dowels and rebar, as a binder for epoxy concrete, and for bonding other dissimilar materials. It is similar to
Product #7 but with a slower cure to allow more time for concrete pours.
Product #9 Mortar Adhesive uses 100% solids Epoxy with graded aggregates. Urethane and Epoxy finish coats provide specific performance characteristics as needed. It is a resin patching, flooring, and/or repair system consisting of 100% solids epoxy resin and aggregates which provide heavy-duty protection at 3/16" to 1/4". When grouted an sealed,
Epoxy.com Epoxy Standard Mortar eliminates porosity and produces a dense, skid-inhibiting finish that will minimize dirt and chemical penetration.
Product #10 Lo-Mod Adhesive and Mortar Binder is a 100% solids epoxy has a low modulus of elasticity (flexibility) and is Low Viscosity. An adhesive used as a binder for epoxy
resin and epoxy hardener mortar systems in patching and grouting applications, as a seal coat for non-skid surfaces outside, and as a primer to insure high bond strength for coatings and patches.
Product #10 Fast Curing Version
Product #10 Cold Temperature Curing Version
Product #11 Epoxy Joint Filler is a 100% solids flexible epoxy joint filler for saw-cut joints of concrete slabs on grade, or to repair existing slabs.
Product #11 Epoxy Joint Filler absorbs the impact and shock of heavy loads and steel wheeled traffic, preventing erosion of control joint edges.
Product #12 Epoxy Primer is a two component, seamless 100% solids epoxy
resin and epoxy hardener primer system with High Chemical Resistance and High Bond Strength. The epoxy may be applied as a primer for most High End Industrial coatings, like Epoxies, MMA, Polyurethane's, Vinyl Esters, Polyesters, etc.
Product #14 Pigmented Mortar - Replace by
Product #24 Epoxy Mortar Resin
Product #15 Chemical Resistant Flooring Resin - a two component, seamless 100% solids epoxy
resin and epoxy hardener resurfacing system with High Chemical Resistance. It may be applied as a coating, or combined with silica sand or Epoxy.com multi-colored quartz aggregate to produce a durable, easy to maintain floor, on both new and old surfaces.
Product #15 Chemical Resistant Flooring Resin has superior clarity and UV stability.
Product #16 Epoxy
Resin and Epoxy Hardner Mortar Resin - Replaced by
Product #24
Epoxy Resin and Epoxy Hardener Mortar Resin
Product #17 Decorative Stone Overlay Adhesive Resin - a two component, 100% solids high-mod epoxy adhesive used for bonding stone and other aggregates in all types of flooring applications. Some uses would include patios, pool decks, walkways and other areas where a long wearing and decorative system is desired.
Product #18 General Purpose Epoxy - a hard set epoxy
resin and epoxy hardenr compound formulated for general use. Product #18 cures at room temperature and is a low viscosity system. This durable, resilient material requires no post curing to achieve permanent bond strength. Mixing ratio of 1 to 1 makes this product easy to use.
Product #18 General Purpose Epoxy solves many difficult bonding, and epoxy mortar problems. Product has the ability to bond to a variety of substrates including cannot dry and hard to dry surfaces.
Product #19 its new stock numbers are Product
#24 (for the pigmented Epoxy Mortar) and Product #28 for
a clear Epoxy Mortar.
Product #20 Epoxy Resin and Epoxy Hardener Grout - a moisture insensitive, two-component, 100% solids epoxy resin system manufactured specifically for use in temperatures of 40°F and below. It is recommended for injection or anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3 1/4 parts of
Product #76 - Epoxy Filler (by volume).
Product #20 Epoxy Grout exceeds most requirements of ASTM C-881-90, Types I, Grade 1, Class A.
Product # 22 Underwater Epoxy Mortar that is a moisture insensitive, two-component, 100% solids epoxy resin. This material is specifically designed for use with the Epoxy.com Fiberglass Systems & Shapes, as well as your own custom forms. Can also be used as self-leveling flooring.
Product # 24 Pigmented Mortar is a multipurpose colored epoxy binder for Epoxy.com
Resin - Epoxy Hardener Mortar Systems This all purpose epoxy resin and epoxy
hardener is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.
Product #24 Fast Pigmented Mortar - Fast Cure
Product #24 Cold Pigmented Mortar - Cold Temperature Cure
Product #25 Epoxy Mortar Kit standard - a 100% solids epoxy resin and specially selected aggregate system. Units are preproportioned for ease of mixing and use on the jobsite. It is a flowable, self-leveling grout, with handling and physical characteristics superior to similar grouts.
Product #26 Epoxy Mortar Kit - This data sheet is here for reference only. This product has been replaced by its new and improved version
Product #26HP.
Product #26HP Epoxy Mortar Kit - is a high strength, non shrink, 100% solids epoxy grout. Epoxy Resin and specially formulated aggregate produce a fluid, non shrink precision grout. Units are preproportioned for ease of mixing and use on the jobsite.
Product #26HP Epoxy Mortar Kit has superior handling and physical characteristics when compared to conventional epoxy grouts. Note: This is not a stock item, please allow up to 2 weeks for us to manufacture this for your order.
Product #27 Long Pot Life Mortar Kit is a preproportioned 100% solids epoxy resin pack and a blend of special aggregate. The pot life of
Product #27 Long Pot Life Mortar Kit is 3 times longer than ordinary epoxy packs; while curing the entire pack, a low exotherm is produced.
Product #28 Epoxy Mortar - Honey Clear Mortar 4:1 Ratio a multipurpose colored epoxy binder for Epoxy.com Mortar Systems This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.
Product #29 Cold Temperature Cure Mortar is a specially formulated binder for cold temperature applications. Able to cure at temperatures as low as 35°F. They are often used in coolers and food preparation areas that require constant low temperatures. Product #29 Cold Temperature Cure EPOXY MORTAR is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.
Product #31 Medium Viscosity Low Modulus Epoxy Resin Mortar System is a two component, 100% solids, Zero (0) VOC moisture insensitive epoxy resin system mixed at a 2:1 ratio. Its low modulus of elasticity permits greater "give" under stress from impact and thermal change. When Components "A" and "B" are mixed together, color will be light straw.
Product #31 Medium Viscosity Low Mod Epoxy exceeds the requirements of ASTM C-881-02, Types I, IV & V, Grade 2, Class B & C.
Product #32 Flexible Epoxy
Resin Membrane is a flexible resin used as an epoxy membrane and as a Product #32 mortar.
Product #32 Flexible Epoxy
Resin Membrane is a two component, 100% solids epoxy used as a base in many Epoxy.com Floor and Mortar Systems.
Product #32 Flexible Epoxy
Resin Membrane resists cracking caused by horizontal substrate movement, providing a crack resistant, resilient, sound absorbent, waterproof, durable floor.
Product #32 Flexible Epoxy
Resin Membrane offers stress-relieving properties for floor slabs that show movement or vibration.
Product #32 is excellent for use in areas such as mechanical equipment rooms, large animal rooms and activity centers.
Product # 33 Epoxy Block Filler
Product #100 Anti-Moisture Entrapment System uses a unique epoxy technology which allows the contractor to install epoxy system on new concrete (4-5 days old) without fear of moisture entrapment.
Product #100 Anti-Moisture Entrapment System exhibits greater than 100 times the permeability of standard epoxy slurries and mortars.
Product #100 Anti-Moisture Entrapment System is used as a base for Epoxy.com Chip and Quartz systems and as a binder for Epoxy.com Resinous Mortar Systems, when moisture is a concern.
Product #115 Epoxy Systems for Modifying Concrete is for modifying concrete is a two component, 2:1 ratio, 100% solids, liquid epoxy resin system. It can be added to conventional concrete or mortar mixes to produce high strength, epoxy modified concrete or mortar mix.
Product #201 Oil Stop Primer for instances petroleum can penetrate the surface of a two component, epoxy-amine undercoating designed to be compatible with petroleum based oil and greases. In many instances petroleum can penetrate the surface of concrete floors to the extent that the oil may not be removed by surface cleaning. If untreated, this oil may migrate back to the surface to cause a delamination.
Product #213 Decoupage Epoxy is a two component, 100% solids, epoxy resin system. When mixed at a 1:1 ratio,
Product #213 Decoupage Epoxy provides a decoupage grade epoxy surface for wood products.
Product #213 Decoupage Epoxy gives a beautiful elegant mar resistant surface that will enhance the look and value of wood for years to come.
Product #214 Tabletop Resin - an all-purpose, low viscosity
epoxy resin ystem for coating wooden counter tops, tabletops, bar tops and similar applications.
Product #214 Tabletop Resin forms a glossy, hard surface, which is resistant to stains.
Product #214 Tabletop Resin has excellent clarity and color retention. It is essentially odorless and can therefore be used in occupied areas
Product #215 Epoxy Polyamine epoxy-polyamide combination, is no longer VOC compliant. Use Epoxy.com 215LVOC instead.
Product # 215LVOC (Low Volatile Organic Content) Epoxy Protective Coating is a two-component, high solids epoxy coating. The material components are Epoxy and high performance polyamide with corrosion inhibitors. It is 100 % reactive. It has a convenient 1:1 mixing ratio by volume and a long pot life to simplify mixing and application.
Product #216 Coal Tar Epoxy
Resin is a two component coal tar epoxy coating, black in color, used to protect steel, concrete structures, timber, and other construction materials in corrosive environments. It meets all requirements of Corp. of Engineers C-200, Federal Specification DOD-P-23236 (SHIPS), and SSPC 16-91.
Product #217 Floor Coating Primer
Product #218 Floor Coating Intermediate
Product #219 Floor Coating Top Coat
Product #220 Rebar Touch Up Epoxy Coating is a two component, 70% solids epoxy coating specially manufactured to touch up damage epoxy coated rebar or to coat rebars not previously protected against corrosion.
Product #220 Rebar Touch Up Epoxy Coating is a two component, 70% solids epoxy coating specially manufactured to touch up damage epoxy coated rebar or to coat rebars not previously protected against corrosion.
Product #222 Water Based Epoxy Coating- is a two component 100% reactive water based multifunctional epoxy resin coating.
Product #222 is manufactured to produce the utmost in performance in a safe, water borne coating.
Product #222 Water Based Epoxy Coating provides excellent resistance to salt intrusion, and excellent adhesion to most common construction substrates.
Product #223 Clear Water Based Epoxy Curing Compound, Sealer and Bonding Agent is a two component water based epoxy curing that is used to both cure and seal concrete and to bond freshly placed concrete to existing concrete. It is ideally suited as a cure and seal for freshly placed concrete. Its chemical resistance makes it ideal to seal: stamped concrete, acid stained concrete, concrete countertops, parapet walls, bridge pier caps, sealing floors in food processing areas, or any other area that requires a durable, chemical resistant concrete sealer.
Product #224 Water Cleanable Epoxy
Resin Mortar Resin is a user friendly, water cleanable, 100% solids epoxy grout and adhesive. Used for grouting ceramic tile, brick pavers, and stone, it is supplied in pre-packaged kits containing resin, hardener, and (in the
Product #225 Water Cleanable Epoxy Mortar Resin Kit) mineral fillers that produce a dense, uniform seal. Typical applications for #224 require resistance to thermal shock, chemicals, and heavy traffic including meat packers, breweries, canneries, bottlers, CIP areas, and pharmaceutical formulators.
Product #225 Water Cleanable Epoxy Mortar Resin Kit
is designed primarily for applications where you for one reason or another
want to use a local aggregate instead of the optimized aggregate that is
comes with the Product #225 Water Cleanable Epoxy
Resin Mortar Kit.
Product #224 Water Cleanable Epoxy
Mortar Resin cannot be used without the addition of aggregate so
unless you have a special aggregate you want to use be sure to order
Product #225 Water Cleanable Epoxy Resin Mortar Kit
Product #225 Water Cleanable Epoxy
Resin Mortar Kit - includes Product #224 Water Cleanable Epoxy Mortar Resin along with the aggregate. Mix the three components together for a ready to use system.
Product #225 Water Cleanable Epoxy
Resin Mortar Kit is a user friendly, water cleanable, 100% solids epoxy
grout and adhesive. Used for grouting ceramic tile, brick pavers, and stone,
it is supplied in pre-packaged kits containing resin, hardener, and (in the
Product #225 Water Cleanable Epoxy Mortar Resin Kit)
mineral fillers that produce a dense, uniform seal. Typical applications for
#225 require resistance to thermal shock, chemicals, and heavy traffic
including meat packers, breweries, canneries, bottlers, CIP areas, and
pharmaceutical formulators.
Product #226 Fast Setting Water Based Epoxy is a Fast Setting Water Based Epoxy Coating is a two component, 100% reactive, water based, multi functional epoxy resin coating.
Product #226 Fast Setting Water Based Epoxy is manufactured to produce the utmost in performance in a safe, water borne coating.
Product #226 Fast Setting Water Based Epoxy provides excellent resistance to salt intrusion, and excellent adhesion to most common construction substrates.
Product #226 Fast Setting Water Based Epoxy is VOC Compliant, Fast Curing, and tintable with standard colorants. It is Internally Flexibilized so it can be applied to metals and plastics. It is water-reducible and easily applied. Special order item only. Requires a minimum quantity. Contact Epoxy.com Tech Support for details.
Product #231 - Water Emulsion Primer and Sealer is a water based epoxy primer/sealer designed to have maximum resin penetration into concrete surfaces to provide high bond strength and adhesion.
Product #231 Water Emulsion Primer and Sealer has very low odor and, therefore, can be used in occupied areas.
Product #231 Water Emulsion Primer and Sealer has the ability to be applied to recently poured (green) concrete and achieve excellent adhesion.
Product #231 Water Emulsion Primer and Sealer is ideal for both new and old concrete surfaces. It is used as a primer for Epoxy.com High Build and Thin Film Coating Systems.
Product #235 Chemical Resistant Novolac Epoxy
Resin Tile Grout and Adhesive is a highly chemical resistant, industrial grade, Novolac epoxy grout for ceramic tile, quarry tile, brick pavers, and stone.
Product #235 Chemical Resistant Novolac Epoxy
Resin Tile Grout and Adhesive is supplied in pre-packaged kits containing resin, hardener, and mineral fillers that produce a dense, uniform seal. Typical applications for
Product #235 Chemical Resistant Novolac Epoxy
Resin Tile Grout and Adhesive require superior resistance to thermal shock, chemicals, and heavy traffic found in the harsh environments of dairies, bakeries, meat packers, breweries, canneries, bottlers, distilleries, and pharmaceutical plants
Product #239 Acrylic Sealer is now called
Product #80
Product #241 Low VOC Acrylic Sealer is a clear acrylic emulsion formulated to create a clear, non-yellowing, protective coating.
Product #241 Acrylic Sealer with Low VOCs provides a tough, UV, and abrasion resistant film that protects surfaces from moisture penetration, staining, dirt, dust, wear, and provides a surface that is easy to clean and maintain.
Product #241 Acrylic Sealer is an excellent choice for both interior and exterior applications.
Product #250 Non-Potable Water Tank Coating is a 100% solids, moisture- insensitive epoxy
resin coating, containing no solvents. It is mixed at a 2:1 ratio, produces a tough, chemical and abrasion-resistant coating for dry or damp concrete, wood or steel surfaces.
Product #255 Mastic High Build Epoxy Coating is a 100% solids, moisture-insensitive, epoxy resin system. When mixed at a 1:1 ratio, by volume, it produces an excellent coating for dry or damp concrete, wood or steel surfaces. It iss used on piles, piers, and concrete or steel tanks where concrete or steel needs to be protected from abrasive environments.
Product #256 Impact and Chemical Resistant Epoxy Coating. is a 100% solids epoxy coating specifically formulated and manufactured to produce a tough, impact resistant coating
Product #260 Corrosion Resistant Epoxy Protective Primer and Coating are two-component, 100% solids epoxy coatings based on multi-functional high performance resin and anti-corrosive pigment.
Product #260 Primer and Coating is used as a two coat system.
Product #260 Corrosion Resistant Epoxy Protective Primer and Coating provides corrosion resistant protection to steel and other metals.
Product #260 Corrosion Resistant Primer and Coating has excellent resistance to chemicals up to 300°F, and hot water resistance at temperatures up to 250°F under continuous immersion. Epoxy.com
Product #260 Corrosion Resistant Epoxy Protective Primer and Coating is formulated in a convenient 2 to 1 ratio, by volume mix ratio and has a long pot life to simplify application. The primer is green and the topcoat is blue. (Other colors are available as special order product.)
Product #260 Corrosion Resistant Epoxy Protective Primer and Coating is particularly effective in applications which entail force curing, either as pre-immersion or during immersion service.
Product #301 Injection
Epoxy Resin, low Modulus - a 100% solids low viscosity epoxy adhesive used to restore cracked structural concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity.
Product #301SC a longer Potlife version of Product #301
Product #301Cold a faster version of Product #301 typically used in Cold Temperature Cure applications, or where a very fast set is needed
Product #302 Injection
Epoxy a 100% solids low viscosity moisture insensitive epoxy adhesive used to restore cracked structural concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity.
Product #303 Low Viscosity
Epoxy Injection Resin a is a two component, 100% solids, moisture insensitive epoxy resin system, mixed at a 2:1 ratio, with a viscosity of light-weight oil. Product #303 exceeds the requirements of ASTM C 881-87, Types I, II, Grade 1, Class "B" and "C". Use neat for grouting damp and dry cracks or as a penetrating sealer on concrete, and wood. May also be mixed with Special Fillers (Products #72-75), to create epoxy mortars.
Product #304 Injection Resin and Mortar Binder is a moisture insensitive, two-component, 100% solids epoxy resin system designed specifically for use in temperatures of 40°F and below. It is recommended for injection or anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3 1/4 parts of
Product #75 Filler (by volume).
Product #304 Injection Resin and Mortar Binder exceeds requirements of ASTM C-881-90, Types I, Grade 1, Class A.
Product #307 Low Viscosity Epoxy Injection Resin and Mortar Binder is an Ultra-Low Viscosity Epoxy Resin System is a two component, 100% solids, moisture insensitive epoxy resin system, mixed at a 2 to 1 ratio, with a very low viscosity for penetrating
cracks. Product #307 Ultra-Low Viscosity Epoxy Resin Systems exceeds the requirements of ASTM C 881 87, Types I, II, Grade 1, Class "B" and "C".
Product #308 Ultra Low Viscosity Injection Resin for Load Bearing Applications is an Ultra-Low Viscosity Epoxy Resin System for use as epoxy injection or low viscosity epoxy mortar resin. It is 100% solids and is mixed 2:1 by volume. Meets or exceeds the requirements for ASTM C881 Types I and IV, Grade 1, Classes B &C.
Product #312 Aliphatic Sprayable Polyurea Coating is a two component sprayable aliphatic polyurea. It dries in seconds to provide a tough chemical and abrasion resistant coating. As an aliphatic polyurea, Product
#312 Aliphatic Sprayable Polyurea Coating is color fast and will resist yellowing from Ultra violet light exposure. Typical working times of one minute or less can be expected. This fast reaction requires a fast, efficient mixing technique so that the mixture can be applied within the short gel times. Impingement mixing from available two-component spray machinery is efficient and entirely adequate.
Product #314 Under Water Coating Replace By
Product #707 Under Water and Splash Zone Epoxy Coating
Product #315 Chip Flooring Product #315 is a seamless, plural component, liquid applied, 100% solids polymeric colored flake floor resurfacing system with superior wear, and chemical resistance. Product #315 with "multi-colored" flakes produces a durable, easy to maintain floor, on both new and old surfaces.
Product #315BC Polymeric Coating and Base Coat for the 315Chip Flooring System. It can also be used as a stand alone coating. If
Product #315BC is used as a stand alone coating over concrete, it is recommended that you first prime with Product #899 Primer.
Product #315BC - Fast Same as Product #315BCPolymeric Coating for Base Coat for the 315Chip Flooring System, but with a fast cure.
Product #315BC-Cold Similar to Product #315BC Polymeric Coating for Base Coat for the 315Chip Flooring System, but with a cold temperature cure.
Epoxy.com #315NH Epoxy Floor Coating is a 100%solids, moisture-insensitive epoxy
resin coating. Epoxy.com #315NH Epoxy Floor Coating mixed at 2 :1 by volume ratio, produces an excellent coating for dry or damp concrete, wood, or steel surfaces.Epoxy.com #315NH Epoxy Floor Coating is available in a summer grade and winter grade formulation. It can be used as a stand alone coating or as a base coat for Epoxy.com Chip Flooring System. It can also be used to replace
Product #315BC Polymeric Coating when a non-hazmat to ship basecoat is required.
Product #316 Fast Set Flooring - a 100 % solids fast setting two-component epoxy resin system. Is made to set fast even in temperatures below freezing. It is recommended for flooring, injection or anchor-bolt grouting in the neat state or as a mortar when mixed Product
#75 Filler. It exceeds most requirements of ASTM C-881-99, Types I and IV , Grade 1, Class A.
Product #600 Flexible
Epoxy Novolac Resin is a two-component, 100% solids epoxy coating based on multi-functional high performance flexibilized resin.
Product #600 Flexible
Epoxy Novolac Resin provides corrosion resistant protection to steel, other metals and concrete. It has excellent resistance to chemicals up to 300°F. It is resistant to continuous immersion in water up to 212°F.
Product #600 Flexible
Epoxy Novolac Resin is formulated in a convenient 1 to 1 ratio, by volume mix ratio and has a long pot life to simplify application.
Product #600 Flexible Novolac
Resin is more effective in applications which entail force curing.
Product #629 Chemical Resistant Conductive Flooring is a 100% solids epoxy Novolac Conductive coating ideal for severe chemical and solvent storage requiring conductive and spark proof surfaces. Applied at a nominal 1/16 inch, the
Product #629 Chemical Resistant Conductive Flooring offers the superior chemical resistance of a Novolac Resin System while maintaining a conductive surface.
Product #630 Novolac Coating/Mortar Binder - a 100% solids epoxy Novolac ideal for harsh chemical and solvent resistant applications. It is ideal for use as a troweled mortar, slurry binder, and coating for concrete and steel in extremely corrosive areas where resistance to 98% sulfuric acid or other strong caustics is needed.
Product #630 Novolac Coating/Mortar Binder is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.
Product #631 - Chemical Resistant Coating has been developed as a coating for exposure to organic acids and other severe chemical environments. It is used widely in the food and chemical industries for protection of concrete, wood, and steel.
Product #631 is suitable for application by brush, roller or spray. Where in-shop production techniques may be utilized and elevated temperature curing is feasible, rapid property development may be achieved by curing at 200° - 250°F (93° - 121°C). This will provide a cured film which may be handled within a relatively short period of time (about 4 hours). Elevated temperature curing will also enhance ultimate physical and chemical resistant properties.
Product #632 Novolac Control Joint Filler is a 100% solids flexible Novolac epoxy Chemical Resistant joint filler for saw-cut joints of concrete slabs on grade.
Product #633 Novolac Coating is a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. It is used in secondary containment, solven storage, pump pads, trenches, and other high exposure areas. It is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.
Product #633 Novolac Coating is commonly used as a seal coat for Epoxy.com MORTAR SYSTEMS where chemical resistant performance is required.
Product #634 Novolac High Temperature Epoxy - is a 100% solids amine cured epoxy Novolac that is solvent free. Suitable for immersion and non-immersion service particularly in aggressive acid and alkali environments with elevated temperatures.Product
#634 Novolac High Temperature Epoxy produces a tough, chemical resistant coating on concrete, iron and non-iron surfaces. As a low viscosity epoxy Novolac it is suitable for hand or spray application.
Product #636 High Temp Chemical Resistant Primer/Topcoat - a 100% solids amine cured epoxy Novolac that is solvent free.
Product #636 High Temp Chemical Resistant Primer/Topcoat is Specifically designed as a Methanol resistant coating.
Product #636 High Temp Chemical Resistant Primer/Topcoat is well suited for use in a wide array of aggressive acids, alkalies and organic solvents. It produces a tough, chemical resistant coating on concrete, iron and non-iron surfaces. As a low viscosity epoxy Novolac it is suitable for hand or spray application.
Product #637 High Temp Coating/Primeris a 100% solids amine cured epoxy Novolac that is solvent free. Suitable for immersion and non-immersion service particularly in aggressive acid environments.
Product #637 High Temp Coating/Primer produces a tough, chemical resistant coating on concrete, iron and non-iron surfaces. As a lower viscosity epoxy Novolac it is suitable as a primer or as a top coating. Excellent against 98% Sulfuric Acid.
Product #638 Glass Filled Novolac
Product #640 Chemical & Heat Resistance
is a two component; 100% solids brush, roll or airless spray applied coating designed to provide cavitation, corrosion and erosion resistance to concrete, metallic and nonmetallic surfaces.
Product #640 Chemical & Heat Resistance
acts as an inert barrier against extremely harsh environmental factors such as low and high PH, temperature extremes, dry and fluid particulate flow and corrosive chemical attack.
Product #641 High Temperature Epoxy
is a moisture-insensitive, two-component, 100% solids epoxy coating. It is especially formulated to protect concrete, steel and wood subject to high temperatures and corrosion.
Product #641LV High Temperature Resistant Epoxy
Resin Mortar Resin
is a two component highly cross-linked Novolac epoxy resin system. It is especially formulated to be used as a high temperature grouting or laminating resin.
Product #641LV High Temperature Resistant Epoxy
Resin Mortar Resin is used to protect concrete, steel and other substrates from high temperatures and corrosion.
Product #642 Multifunctional High Chemical Resistance Epoxy
Resin Coating/Bonder is a two component, 100% solids, one coat trowel grade or grout pump applied protective coating designed to provide cavitation, erosion and corrosion resistance to metallic and non-metallic surfaces.
Product #642 Multifunctional High Chemical Resistance Epoxy Coating/Bonder acts as a barrier against extremely harsh environmental factors such as low and high PH, temperatures extremes, dry and fluid particulate flow and corrosive chemical attack.
Epoxy.com Product #643 Highly Chemical Resistant Coating
is a solvent free, high functionality Novolac epoxy
resin coating suitable for immersion and non-immersion service. Designed specifically as a Methanol resistant coating.
Epoxy.com Product #643 Highly Chemical Resistant
Epoxy Resin Coating
is well suited for protection in a wide array of aggressive acids, alkalies and organic solvents. It produces a tough, chemical resistant coating on ferrous and non-ferrous metals and concrete.
Product #644 High Temp Chemical Resistant Coating. Similar to
Product #641LV, but with fillers to make it thicker.
Product #646 Heat Resistant Translucent Black Coating is especially formulated to be used as a high temperature grouting or laminating resin. It is also used to protect concrete steel, or other substrates from high temperatures and corrosion. It is similar to
Product #641 but it does not
have the pigments that the Product #641 has.
Product #647 High Temperature Epoxy
Resin Coating and High Temperature Epoxy Resin Mortar and High
Temp Epoxy Laminating Resin is a two component highly cross-linked Novolac epoxy resin system.
Product #647 High Temperature Epoxy Coating and High Temperature Epoxy Mortar is especially formulated to be used as a high temperature potting or laminating resin. It is used to protect parts from high temperatures and corrosion.
Product #647 High Temperature Epoxy Coating and High Temperature Epoxy Mortar is 100% solids and has a convenient 2:1 by volume mix ratio and is easy to apply.
Product #648 Chemical Resistant
Epoxy Coating
is a two component high performance epoxy resin formulated with a convenient 1 to 1 mix ratio.
Product #648 Chemical Resistant
Epoxy Coating
has been developed as a coating for exposure to organic acids and other severe chemical environments. It is used widely in the food and chemical industries for protection of concrete, wood, and steel.
Product #648 Chemical Resistant
Epoxy Coating
is suitable for application by brush, roller or spray. Where in-shop production techniques may be utilized and elevated temperature curing is feasible, rapid property development may be achieved by curing at 200° - 250°F (93° - 121°C). This will provide a cured film which may be handled within a relatively short period of time (about 4 hours). Elevated temperature curing will also enhance ultimate physical and chemical resistant properties.
Product #650 Resurfacing Grade Epoxy
is a two-component, 100% solids, brushable ceramic, reinforced polymeric compound which has outstanding wear-resistance against abrasion, erosion/corrosion and cavitation in a fluid-flow environment.
Product #651 Ceramic Filled Epoxy Mortar is a two-component, 100% solids, ceramic reinforced, trowelable polymeric compound which can be used to repair virtually any metal surface that has been damaged by erosion/corrosion, cavitation or abrasion.
Product #652 Metal Filled Trowel Grade Epoxy is a two-component, 100% solids, metal-reinforced polymeric compound which can be used to repair virtually any metal surface that has been damaged, cracked or worn.
Product #653 Emergency Epoxy Liquid Grade
Product #654 Metal Filled Internally lubricated Trowel Grade
Epoxy.com Product #671 Conductive
Epoxy Resin Primer/Sealer is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces.
Epoxy.com Product #671 Conductive
Epoxy Resin Primer/Sealer is ideal for both new and old concrete surfaces. Epoxy.com Product #671 Conductive
Resin Primer/Sealer provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive primer when used with
Product #674 Electro-Static Dissipating Urethane Topcoat and Epoxy.com Conductive Systems.
Product #672 Conductive Epoxy
Resin is a two component, 100% solids epoxy/aggregate material that utilizes the latest in conductive floor technology.
Product #672 Conductive Epoxy
Resin can be installed as a coating or as a component to Epoxy.com Flooring Systems. It can also include
Epoxy.com Elastomeric Membranes to produce waterproof, crack resistant Systems. Typical Uses of include: Ammunitions Facilities, Paint and Solvent Storage Areas, Electronic Component Plants Hazardous Materials Storage Areas
Product #675 Electrostatic Dissipating Water Borne Epoxy Topcoat is a pigmented, water emulsion epoxy electro-static dissipative finish designed to have maximum penetration into concrete surfaces to provide high bond strength and adhesion. It has very low odor and can be used in occupied areas as a finish sealer in Thin-Film Electro-Static Dissipative Coating Systems.
Product #676 Novolac Epoxy Chemical Resistant Conductive
Epoxy Resin Floor Coating is a 100% solids - Zero (0) VOC epoxy Novolac Chemical resistant conductive (anti-sparking) epoxy flooring and floor coating system ideal for severe chemical and solvent storage requiring a chemically resistant conductive and spark resistant surface.
Product #677 Electro Static Dissipative (ESD)/ Conductive
Epoxy Resin Coating is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by modifying the underlying system components and thickness.
Product #677 has very low odor making it suitable for use in occupied buildings and has high bond strength and adhesion to concrete and other surfaces.
Product #701 Flexible
Epoxy Resin Bonder/Adhesive is a two component, 100% solids,
with a 1:1 ratio adhesive formulated to give a permanent bond to ceramic, metal, concrete and elastomeric surfaces. It is thixotropic, non-sag, and is easily applied by trowel.
Product #702 Traffic Marker and Anchor Bolt Adhesive
Epoxy Resin is a two component, 1:1 ratio, 100% solids, moisture insensitive epoxy resin system manufactured to bond delineators and traffic markers to median barriers, parapets, and roadways. It is a normal setting adhesive for use in temperatures above 50° F.
Product #702 Traffic Marker and Anchor Bolt Adhesive will bond to steel, concrete, and asphalt. It exceeds the requirements of AASHTO M237 Type IV.
Product #703 Flexible Gel Adhesive is a non-sagging material that is ideal for repairs on vertical or
overhead surfaces. It exceeds the requirements of ASTM C 881-87, Types I, II, and III Grade 3, Class "B", "C", "E" and "F".
Product #704 Emergency Epoxy is a rapid setting, two component, 1:1 ratio epoxy
resin adhesive. It sets in six minutes and can be put into service in one hour regardless of temperature. It was designed to bond metals, glass, concrete and wood in a matter of minutes.
Product #705 Two Component Flexible Epoxy
Resin Adhesive has been replaced by
Product #701 Flexible
Epoxy Resin Bonder
Product #706 Heat Resistant
Epoxy Resin Bonder/Mortar is a 100% solids, moisture insensitive epoxy adhesive and repair material. When A and B Components are mixed they produce a gel consistency similar to petroleum jelly, which will not sag or run on a vertical or overhead surface application.
Product #707 Splash Zone & Under Water Epoxy
Paste is a epoxy resin and hardener system
that is moisture-insensitive, two-component, 100% solids epoxy-resin system. When
Product #707 Splash Zone & Under Water Epoxy is mixed at a 1:1 ratio, by volume, this product produces a paste-like material that is ideal for protection or restoration of concrete, steel and timber piles and other structural elements in marine environments.
Product #711 is protective
epoxy resin coating designed to provide cavitation, erosion and corrosion resistance to metallic and non-metallic surfaces.
Product #711 acts as a barrier against extremely harsh environmental factors such as low and high PH, temperatures extremes, dry and fluid particulate flow and corrosive chemical attack.
Product #714 Precast Segmental Adhesive is a 100% solids, gelled epoxy adhesive formulated to the requirements of ASTM C-881-90, Type VI, Grade 3, Class D, E, or F. AASHTO M-235-90 duplicates the technical requirements of ASTM -C-881-90.
Product #720 Cove Base Binder
- can be used to install an integral cove base for most Epoxy.com Flooring Systems, to provide seamless wall to floor protection.
Product #830 Moisture Vapor treatment is a two component modified epoxy system designed to seal concrete and reduce moisture vapor transmission prior to applying finished flooring.
Product #830 Moisture Vapor treatment has proven to reduce moisture vapor emissions and be resistant to damage from high alkalinity.
Product #830 Moisture Vapor treatment is an environmentally friendly material containing no hydrocarbons or other solvents making it zero (0) VOC.
Epoxy.com Product 870 - 65% Solids - Penetrating Epoxy Sealer is a two-component penetrating epoxy sealer (with very high solids) designed for superior protection of new concrete or for prolonging the serviceability of partially-deteriorated concrete. The sealer is a low to medium viscosity material and is capable of providing an effective membrane barrier to inhibit moisture migration and corrosive chemical penetration. In the cured state
Epoxy.com Product 870 - 65% Solids - Penetrating Epoxy Sealer allows moisture vapor transmission; it seals off moisture entry but still allows the concrete to breath. When applied to concrete placed and finished in accordance with standards defined in ACI 201 (Guide to Durable Concrete),
Epoxy.com Product 870 - 65% Solids Penetrating Epoxy Sealer) greatly improves wear resistance of the concrete surface, slows down the corrosion of reinforcing steel and adds many years' life to the structure.
Epoxy.com Product 870 - 65% Solids Penetrating Epoxy Sealer) has a solids content of over 65% after curing. It may be applied to dry surfaces at temperatures of 40�F or above.
Product #1200 Epoxy Organic Zinc Rich Primer is a two component epoxy primer which provides both barrier and sacrificial protection against steel corrosion.
Product #1200 Epoxy Organic Zinc Rich Primer promotes adhesion, dries rapidly, and can be either shop or field applied.
Product #1700 Electrical Epoxy
Resin Potting Compound used as an electrical encapsulation material where ease of use and high electrical resistivity are needed. It is a low viscosity, low odor material with a pourable viscosity. It has a convenient 1 to 1 by volume mix ratio and a long pot life.
Product #1700 Electrical Epoxy Potting Compound has a very low exotherm on curing allowing for large parts with extremely low shrinkage.
Above is a list of just Epoxy.com Epoxies. You can find a complete listing of all Epoxy.com Products at www.epoxy.com/products.aspx
|