Epoxy Bonding Agent
Bonding Fresh Concrete to Hardened Concrete
Epoxy.com Product #2007
Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 is a
two component, 100% solids epoxy resin system designed to bond new concrete to
old and other materials to concrete. It has a convenient 2:1 mix ratio, by
ASTM C-881-90, Types I, II, IV and V, Grade 2, Class "B" and "C"
volume with a viscosity similar to heavyweight oil. Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 (adhesive) exceeds the requirements of ASTM
C-881 Type II, Grade 2, Class "B" "C" "D" and E.
- Meets ASTM C-881 Type II, Grade 2, Class "B" "C"
"D" and E.
- Is a Moisture Insensitive Epoxy Adhesive
- Multi-Function Epoxy - makes it suitable for many types of uses
- Very Little Odor
- 100% Solids
- Zero (0) VOC Epoxy Adhesive - No VOC means it meets the
strictest low VOC standards
Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
(adhesive) can be used for:
- New Concrete to Old Concrete Epoxy Binding Resin
- Epoxy Grouting Machine Base Plates
- Anchor Bolts Setting Epoxy
- An Epoxy Floor Topping with Good Chemical Resistant Properties
- A Skid-Resistant Epoxy Surface on Concrete, Steel or Timber
- A Protective Epoxy Coating.
When Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 is used as an adhesive, bonding new concrete to
existing surfaces, coat the existing area (concrete, steel, aluminum, wood) at a
rate of 100 square feet per gallon (9 m2) on smooth surfaces, 60 square feet on
rough (6 m2). Apply topping while Epoxy.com Product #7 All Purpose Epoxy
(adhesive) is tacky; if dry, recoat.
When Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
is used as a protective coating, apply the material at a rate of 200 square
feet per gallon per coat (8 mils) (19 m2/3.79 L -or- 5 m2/L).
Stir Component "B" thoroughly before combining with Component "A". Combine 1
part volume of Component "A" with 1 part by volume of Component "B" for not less
than (3) three minutes, using a slow-speed drill motor (300 to 600 rpm) and
Epoxy.com Mixing Paddle for a uniform gray mixture. Scrape sides and bottom.
Avoid entrapping air in mixture. Apply immediately after mixing to properly
Surface must be clean and sound. Remove rust, grease and curing compounds by
best means available. Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
may be applied to dry or damp surfaces, but not in standing water. Apply by
brush, roller or spray. Place fresh concrete while Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
(adhesive) is still tacky. If epoxy hardens simply apply another coat.
||2:1 by Volume
|Bond Strength PSI Min.
|Gel Time (150 g mass @ 70° F)
|Flash Point in °F
||3,500 to 4,500 cps
||24 hr. (80% ultimate strength)
|Lineal Coefficient of Shrinkage
|Compressive Modulus (psi)
|Compressive Yield (psi) at 7 day cure
|Tensile Strength @ 75 degrees F at 7 days
||4000 P.S.I (34.5 MPa)
|Flexural Strength (psi)
|Heat Deflection Temperature °F
|Elongation at break (%)
|Thin Set Film set time hours
|Peak Exotherm °F
|Coverage @ 30 mils
||53 sq. ft./gal
||1.5 gal units, 3 gal units, 15 gal units
Application of Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007
to surfaces with a temperature below 50°F (10.0°C) prolongs cure. Do not use if
surface temperature is below 50°F (10.0°C).
Epoxy Fresh Concrete to Hardened Concrete Adhesive #2007 is excellent against distilled water, most inorganic
acids and alkalies and moderate against alcohols or aromatic solvents.
NOTICE TO BUYER
DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
Products are manufactured to strict quality assurance specifications and that
the information supplied by us is accurate to the best of our knowledge. Such
information supplied about our products is not a representation or a warranty.
It is supplied on the condition that you shall make your own tests to determine
the suitability of our product for your particular purpose. Any use or
application other than recommenced herein is the sole responsibility of the
user. Listed physical properties are typical and should not be construed as
specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER
INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM
ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE
MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO
WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT
INFRINGE UPON ANY PATENT. We shall have no liability for incidental or
consequential damages, direct or indirect. Our liability is limited to the net
selling price of our product or the replacement of our product, at our option.
Acceptance of delivery of our product means that you have accepted the terms of
this warranty whether or not purchase orders or other documents state terms that
vary from this warranty. No representative is authorized to make any
representation or warranty or assume any other liability on our behalf with any
sale of our products. Our products contain chemicals that may CAUSE SERIOUS
PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW
ALL PRECAUTIONS TO PREVENT BODILY HARM.
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Novolac Epoxy] [Primers Sealers]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]