Epoxy.com Product #1 Cold Cure Epoxy Coating
Epoxy Polyurethane Polyester MMA - Methyl Methacrylate, other Resin Systems Over 350 Products Since 1980 Contact Us

Epoxy.com Product #1 Cold

100% Solids Cold Temperature Cure Epoxy Coating

Cures at Temperatures as Low as 35°F

100% solids - zero (0) VOC - meets the lowest VOC requirements


DESCRIPTION

Epoxy.com Product #1 Cold Temperature Cure Epoxy Coating is 100% solids and  specially formulated coatings for cold temperature applications. Able to cure at temperatures as low as 35°F. It is has Zero (0) VOCs. Since it has no VOCs, it has no solvent so it meets the strictest possible standard for a low VOC coating. It is often used in coolers and food preparation areas that require constant low temperatures. Product #1 Cold Temperature Cure Epoxy Coating is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.

ADVANTAGES

  • Low temperature cure
  • Low odor during application and cure-will not taint foods
  • Superior stain and chemical resistance
  • Bonds well to cool, damp substrates
  • Zero (0) VOC- no VOC - No solvent  means it meets even the strictest low VOC standards
  • 100% Solids

CONSIDERATIONS

  • Substrate temperature must be a minimum of 35°F
  • Substrate must be free of dirt, waxes, curing agents, and other foreign materials

COMPOSITION

Epoxy.com Product #1 Cold Temperature Cure Epoxy Coating is 100% Solids Epoxy Resins and  Epoxy Hardeners

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates to receive Epoxy.com Product #1 Cold Temperature Cure COATING must be properly prepared. For more information see Epoxy.com Surface Preparation Guide and  Contact Epoxy.com Technical Service Department with your questions.

INSTALLATION

Epoxy.com Product #899 Cold Cure Primer is recommended for concrete surfaces.  Installation of Epoxy.com Product #1 Cold Temperature Cure COATING is normally spread with with the "dip and roll" method or a notched trowel or squeegee and back-rolled with a medium or short nap roller. Care should be taken to minimize the entrapment of air caused by over-rolling.

CLEAN UP

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.

COVERAGE

Epoxy.com Product #1 Cold Temperature Cure COATING is typically applied in two or more coats of 160-200 square feet per gallon per coat.

COLOR SELECTION

Epoxy.com Product #1 Cold Temperature Cure COATING is available in Light Grey, Sand, Old Gold, Mocha, Brick Red, Taupe, Dark Grey, Slate Blue, Colonial Green, Charcoal, Caramel, Gem Grey, White Sand, White, and Black. Safety Yellow, Deep Blue, Ivy, and custom colors available at an additional charge.

Epoxy.com Product #1 Cold cure Color Chart |100% Solids | Zero (0)VOC
Click the picture
of color card for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

TECHNICAL DATA

Viscosity @ 75°F 1,000 cps
Mixing Ratio 2 Parts A to 1 Part B by Volume
Solids Content 100%, by volume
Volatile Organic Content (VOC)0
Weight per gallon10.0-11.5 pounds per gallon, mixed

CURE/DRY TIME

Pot Life15 minutes @ 75°F
Dry to Touch2-3 hours @ 75°F; 14-16 hours @ 35°F
Re-Coat3-4 hours @ 75°F; 14-16 hours @ 35°F
Light Traffic5-6 hours @ 75°F; 24 hours @ 35°F
Full Cure & Maximum Resistance5 days

Other customers who visited this page also visited:

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems ,
Since 1980 - Over 33 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time) .
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright © 1994-2015 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.