|
|
EpoxySystems' Product #633100% Solids Hi-Solids Epoxy Novolac Coating
DESCRIPTION | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| PHYSICAL PROPERTIES | |
| Color | See color chart below |
| Solids Content | 100% |
| Gloss 60 F | 100 |
| Mix Ratio | 2A to 1B by volume |
| Pot Life | 20 minutes @ 75 F |
| VOC | 0% |
| DRY TIME | |
| Foot Traffic | 10-12 hours |
| Recoat - Minimum | 4 - 12 hours (Depending on Temperature) |
| Recoat - Maximim | 24-36 hours (Depending on Temperature) |
| Service | 5 days |
| CHEMICAL RESISTANCE | |
| REAGENT | RATING |
| Acetic Acid 20% | R |
| Urea | R |
| Acetone | L |
| Bleach | R |
| Citric Acid | R |
| Crude Oil | R |
| Skydrol | R |
| Diesel Fuel | R |
| Hydraulic Fluid | R |
| Sodium Hydroxide - 50% | R |
| Ethylene Glycol | R |
| Sulfuric Acid-98% | R |
| Fatty Acids | R |
| Toluene | R |
| Gasoline | R |
| Lactic Acid | R |
| Methyl Ethyl Ketone | L |
| Nitric Acid | R |
| Hydrochloric Acid-36% | R |
| Xylene | L |
R-Recommended for Intermittent Immersion. L-Limited recommendation, occasional spills.
| PERFORMANCE PROPERTIES | |
| Tensile Strength ASTM-D-638 | 10,400 p.s.i |
| Adhesion to concrete ACI Committee 403 | 300 p.s.i - 100% concrete failure |
| Hardness ASTM-D-2240 | 86 Shore D |
| Abrasion Resistance ASTM-C-501 CS-17 Wheel | 30 mg lost |
| Service Temperature MIL- D-3134F | Up to 180-325 degrees F. Dry Heat |
| Elongation | 2.5% |
Click
the picture of color card below for a larger version of this picture
of the color chart.
Please
note: The picture to the right is a photographic reproduction of the
color card for this product. The photo reproduction process and your
monitor and/or printer will change these colors. This chart is to give you
an idea of the colors available and not intended for critical color selections.
You can estimate using the spreadsheet below or by using our NEW Coating Calculator.
Download the above spreadsheet in Microsoft Excel Format worksheets/CoatingsCalculator.xls
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
