|
|
EpoxySystems' Product #2100% Solids Epoxy Based Chemical Resistant Coating
GENERAL DESCRIPTION Product #2 a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. APPLICATIONS Typical Uses:
ADVANTAGE
SURFACE PREPARATION Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast immediately prior to application. See EpoxySystems' Surface Preparation Guide form more details. MIXING INSTRUCTIONS Temperature of Product #2 must be 50 degrees F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle. APPLICATION Product #899 Primer is recommended for concrete surfaces. Apply Product #2 with a roller, brush, or spray equipment. Two coats are recommended. Thickness per coat should be 7-10 mils. Seven days cure time is required to reach maximum chemical resistance. For more information before installing please see installation tips at https://www.epoxy.com/install.htm. LIMITATIONS Refer to Product #2 Chemical Resistance Chart for field tested results of common industrial chemicals that Product #2 has been exposed to. New concrete should be at least 28 days old. Temperature of substrate must be above 50 degrees F. DO NOT thin. SAFETY PRECAUTIONS Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves. CLEANING All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
Download the above spreadsheet in Microsoft Excel Format worksheets/CoatingsCalculator.xls
EpoxySystems'TM Product #2CHEMICAL RESISTANCE CHARTCHEMICAL TEST TIME MONTHS
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Reagent | CHEMICAL TEST TIME MONTHS | ||||
| 1 | 3 | 6 | 9 | 12 | |
| WATER, DISTILLED | + | + | + | + | + |
| SEAWATER | + | + | + | + | + |
| SULFURIC ACID, 10% | + | + | + | + | S |
| SULFURIC ACID, 30% | + | + | + | - | - |
| SULFURIC ACID, 70% | + | + | + | - | - |
| HYDROCHLORIC ACID, 10% | + | + | + | + | + |
| HYDROCHLORIC ACID, 20% | + | + | + | + | + |
| HYDROCHLORIC ACID, 36% | + | + | + | + | + |
| HYDROCHLORIC VAPOR | + | + | + | + | + |
| ACETIC ACID, 5% | + | + | - | - | - |
| ACETIC ACID, 10% | - | - | - | - | - |
| AMMONIUM HYDROXIDE, 10% | + | + | S | S | - |
| AMMONIUM HYDROXIDE, 25% | + | S | - | - | - |
| SODIUM HYDROXIDE, 20% | + | + | + | + | + |
| ACETONE | - | - | - | - | - |
| BUTANONE | - | - | - | - | - |
| BUTYL ACETATE | + | + | S | S | S |
| DIACETONE ALCOHOL | + | + | + | + | + |
| CELLOSOLVE | S | S | S | S | S |
| ETHANOL, 50% | + | + | + | - | - |
| ETHANOL, 96% | - | - | - | - | - |
| OCTANOL | + | + | + | + | + |
| XYLENE | + | + | + | + | + |
| TOLUENE | + | + | + | + | + |
| BENZENE | + | + | S | S | S |
| SKYDROL | + | + | + | + | + |
| TRICHLOROETHYLENE E | + | + | S | S | S |
| CRUDE OIL | + | + | + | + | + |
| GASOLINE, 98 OCTANE | + | + | + | + | + |
| ACETAL GLACIAL | - | - | - | - | - |
| CITRIC 10% | + | + | + | + | + |
| CITRIC 50% | + | + | + | + | + |
| FATTY ACID (LINSEED) | + | + | + | + | + |
| LACTIC (DAIRY PRODUCTS) | + | + | + | + | + |
| NITRIC 10% | + | - | - | - | - |
| NITRIC 20% | + | - | - | - | - |
| NITRIC 30% | + | - | - | - | - |
| PHOSPHORIC | - | - | - | - | |
| ALLYL CHLORIDE | + | S | S | S | S |
| CARBON TETRACHLORIDE | + | + | + | + | + |
| DIETHYLENE TRIAMINE | - | - | - | - | - |
| ETHYL ALCOHOL | - | - | - | - | - |
| ETHYLENE DIAMINE | - | - | - | - | - |
| FORMALDEHYDE | - | - | - | - | - |
| METHYL ETHYL KETONE | S | - | - | - | - |
|
ISOPROPYL ALCOHOL |
+ | + | + | + | + |
| METHYL ISOBUTYL CARBINOL | + | + | + | + | + |
| METHYL ISOBUTYL KETONE | S | S | S | S | S |
| MINERAL SPIRITS | + | + | + | + | + |
| DETERGENTS ANIONIC 2% | + | + | + | + | + |
| CALCIUM HYPOCHLORITE 5% | + | + | + | + | + |
|
SODIUM CHLORITE 25% |
+ | - | - | - | - |
| SODIUM HYPOCHLORITE 5% | + | - | - | - | - |
| STAIN RESISTANCE | |||||
| BUTTER | + | + | + | + | + |
| CITRUS JUICES | + | + | + | + | + |
| COFFEE | + | + | + | + | + |
| COLA | + | + | + | + | + |
| GREASE | + | + | + | + | + |
| HAIR TONIC | + | + | + | + | + |
| INK | + | + | + | + | + |
| LARD | + | + | + | + | + |
| LIPSTICK | + | + | + | + | + |
| LIQUOR | + | + | + | + | + |
| MILK | + | + | + | + | + |
| MINERAL OIL | + | + | + | + | + |
|
MUSTARD |
+ | + | + | + | + |
| VINEGAR | + | + | + | + | + |
| SANDBLASTED STEEL PANELS, COATED WITH AN AVERAGE. OF 14 MIL FILM THICKNESS, IMMERSED IN THE VARIOUS MATERIAL FOR UP TO ONE YEAR | |||||
Click
the picture of color card below for a larger version of this picture
of the color chart.
Please
note: The picture to the right is a photographic reproduction of the
color card for this product. The photo reproduction process and your
monitor and/or printer will change these colors. This chart is to give you
an idea of the colors available and not intended for critical color selections.
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
