Chemical Resistant Conductive Flooring
Epoxy.com Product #630 Conductive
Epoxy.com Product #630 Conductive Novolac Epoxy Chemical Resistant Conductive
Floor Coating is a 100% solids epoxy Novolac chemical resistant conductive
coating ideal for severe chemical and solvent storage requiring conductive
and spark proof surfaces. Applied at a nominal 1/16”, Epoxy.com
Product #630 Conductive Novolac Epoxy Chemical Resistant Conductive Floor Coating offers the superior chemical resistance of an
Epoxy.com Novolac Epoxy Resin System
while maintaining a conductive surface.
- Low viscosity for
improved handling during application.
- Exhibits excellent
resistance to strong acids, alkalis and most industrial chemicals and
- 100% Solids—low odor
application and cure (0-VOC).
- Bonds well to cool,
- Conductive & non
sparking, 25,000 to 1,000,000 ohms resistance.
- Substrate to receive Epoxy.com Product #630
Conductive Novolac Epoxy Chemical Resistant Conductive Floor Coating temperature
must be a minimum of 50°F.
- Substrate must be free
of dirt, waxes, curing agents and other foreign materials.
- Steel surfaces to receive Epoxy.com Product #630
Epoxy Chemical Resistant Conductive Floor Coating must be
free of grease and oils. Abrasive blast to SSPC-SP-3.
- Refer to Epoxy.com Surface Preparation Guidelines for substrate requirements.
100% Solids, modified polyamine, cured epoxy novolac resin and fillers
Surface Preparation is the most critical portion of any successful
resinous flooring system application. All substrates must be properly
prepared as outlined in Epoxy.com Surface Preparation Guidelines.
Contact epoxy.com technical service department is
pleased to answer any questions.
Installation of Epoxy.com Product #630 Conductive Novolac Novolac Epoxy
Chemical Resistant Conductive Floor Coating will vary with application.
Normally spread with a trowel or squeegee and lightly back-rolled with a
medium or short nap roller. Care should be taken to minimize the
entrapment of air caused by over rolling. For complete instructions, consult installation guide or Epoxy.com
Technical Support Department
Clean skin with soap and water. Tools and equipment should be
cleaned with xylene or lacquer thinner.
Epoxy.com Product #630 Conductive Novolac Epoxy Chemical
Resistant Conductive Floor Coating will yield approximately 32 mils when
spread at 50 ft2 per gallon. Two coats required. Epoxy.com
Check Epoxy.com Electrostatic Dissipative (ESD) and
Conductive Flooring Calculator to calculate
Epoxy.com Conductive and Electrostatic Dissipative (ESD) material
requirements for your installation.
Epoxy.com Product #630 Conductive Novolac Epoxy Chemical
Resistant Conductive Floor Coating is available in Standard Colors and
Custom Colors as approved.
|Viscosity @ 75°F
|Mixing Ratio by volume
||2 Part A to 1 Part B by Volume|
|Solids Content by volume
||100% by volume|
|Volatile Organic Content
|Weight per gallon, mixed
||11.0-11.5 lbs. per gallon mixed|
||20-25 min. @75°F|
|Dry to Touch
||6-7 hours @ 75°F|
||8-12 hours @ 75°F|
||24 hours @ 75°F|
|Full Cure & Maximum Resistance
|Acetic Acid-10%, 30%
|Methyl Ethyl Ketone
|R-Recommended for continuous service|
L-Limited Recommendation, occasional spills
*-May cause slight stain or discoloration
After completing the application of Epoxy.com Product #630
Novolac Epoxy Chemical Resistant Conductive Floor Coating, the
installer should provide the owner with maintenance instructions. Epoxy.com
Product #630 Conductive Conductive Chemically Resistant Novolac Floor Coating is easily cleaned with neutral soaps or detergents.
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2014 (providing online information about the
right product for the right job for 20 years) EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a division of Epoxy Systems, Inc. (hereinafter known as
"Supplier" warrants its products (when properly stored) for the period of
time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylates
and Polyurethanes Six (6) months. Supplier warrants that its products
will be free of manufacturing defects and will be in conformity with
published specifications when handled, stored, mixed and applied in
accordance with recommendations of Supplier. If any product fails to meet
this warranty, the liability of Supplier will be limited to replacement of
any non-conforming material if notice of such non-conformity is given to
Supplier within the warranty period for the material (as indicated above),
or within 1 year of the delivery of materials (whichever is sooner).
Supplier may in its discretion refund the price received by Supplier in lieu
of replacing the material. No customer, distributor, or representative of
Supplier is authorized to change or modify the published specifications of
this warranty in any way. No one is authorized to make oral warranties on
behalf of Supplier. In order to obtain replacement or refund the customer
must provide written notice containing full details of the non-conformity.
Supplier reserves the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S
OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN
ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR
LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. All quotes and sales subject to availability.
Many of our products are made
on an individual order basis. Unless authorized by us
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Novolac] [Primers Sealers]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]