Epoxy.com Product #214100% Solids Epoxy Casting Tabletop and Bar Top ResinGENERAL DESCRIPTIONEpoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin is an all-purpose, low viscosity Epoxy System for coating wood and concrete counter tops, tabletops, bar tops and similar applications. Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin is commonly used as a clear self-leveling flooring material, where an extremely flat and level floor is required over concrete and wood. Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin is used extensively for ultra flat leveling of surfaces under equipment, where a very strong ultra flat bearing surface is a must. It is also used successfully for ultra flat floors for stages, dance floor, and clean rooms. Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin is used as a clear adhesive matrix for specialty colored glass and colored aggregate flooring and tiles. Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin forms a glossy, hard surface, which is resistant to stains. It is also used extensively as a water clear epoxy casting resin. Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin has excellent clarity and color retention. Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin has zero (0) VOC making it essentially odorless and can therefore be used in occupied areas. ADVANTAGES
CONSIDERATIONS
SURFACE PREPARATIONSurface Preparation is the most critical portion to any successful epoxy application. All substrates to receive Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin must be properly cleaned and prepared. Substrate must be free of oil, paint, sealer, caulking, and all other contamination that will interfere with the bonding of this material. Please see Surface Preparation. Contact Epoxy.com for more details. MIXING INSTRUCTIONSStir each component separately. Combine 2 parts A to one part B by volume into a clean container. Stir for three minutes, with an Epoxy.com Mixing Paddle, scrapping bottom and sides of container frequently. Do not add thinners.
APPLICATIONApplication of Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin will vary with application method. Be careful not to incorporate bubbles into the coating. Typical pours are in the 1/16 inch to 1/2 inch thick range per coat. If a second coat is desired, remove all dust, if more than 24 hours after the last coat lightly sand, and then apply second coat. SAFETY PRECAUTIONSFor industrial use only. Keep away from children. Refer to the Material Safety Data Sheets (MSDS forms) pertaining to this product before using. Avoid contact with skin or eyes. Prolonged or repeated exposure may cause eye and skin irritation. If skin contact occurs, wash immediately with soap and water. If contact with eyes occurs, flush eyes as required with clean water and seek medical help. Use safety glasses with side shields and wear protective rubber gloves. CLEANINGRemove Epoxy.com Product #214 Epoxy Casting-Epoxy Tabletop-Epoxy Bar Top Resin from all tools and equipment before the system gels. Use MEK, Acetone, or any lacquer solvent.
R=Recommended for continuous service L=Limited recommendation, occasional spills. Coverage: 231 cubic inches per gallon. At 1/8 inch thick 12.8 SF Per gallon. Use the calculator below to double check your estimate. Material Calculator: | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
