[Home] [Catalog of Products] [Where to Start with Epoxy] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Coatings] [Conductive]  [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy]  [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Wood Filler] [Who is Epoxy.com] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

Epoxy.com Product #675

Electro-Static Dissipative Water Emulsion Finish


DESCRIPTION

Epoxy.com PRODUCT #675 is a pigmented, water emulsion epoxy electro-static dissipative finish designed to have maximum penetration into concrete surfaces to provide high bond strength and adhesion. Epoxy.com PRODUCT #675 has very low odor and can be used in occupied areas as a finish sealer in Thin-Film Electro-Static Dissipative Coating Systems.

ADVANTAGES

  • Low Odor During Application and Cure
  • Fast Dry and Re-coat Time
  • Easy Clean-up
  • Can be used on Damp/Green Concrete
  • Greatly Reduces the Probability of Concrete Outgassing
  • Provides a conductive finish in the range of 1,000,000 to 1,000,000,000 ohms resistance

CONSIDERATIONS

  • Substrate temperature must be a minimum of 50?F and relative humidity below 85% for proper curing
  • Substrate must be free of dirt, waxes, curing agents, and other foreign materials

COMPOSITION

Waterborne Epoxy Resin and Conductive Fillers

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com TECHNICAL BULLETINS. Work must be performed by trained or experienced contractors or maintenance personnel. Epoxy.com Technical Service department is pleased to answer any questions.

INSTALLATION

Mix each component of Epoxy.com PRODUCT #675 prior to combining. Mix 1 part Part A with 4 parts Part B and allow to stand 15-30 minutes before applying. Roll mixed Epoxy.com PRODUCT #675 at a rate of 275-300 ft2 per gallon with a short nap roller. Care should be taken to avoid puddles. Do not build a film of the sealer and roll out so that it soaks into the concrete. Two coats are necessary to insure uniform wetting and coverage. For complete installation instructions, contact Epoxy.com Technical Service.

CLEAN UP

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COLOR SELECTION

Epoxy.com PRODUCT #675 is available in most Epoxy.com Standard Colors.

COVERAGE

Epoxy.com PRODUCT #675, when applied at 300 ft2, yields 2-2.5 mils dry film.

TECHNICAL DATA

Viscosity @ 75?F 300-400 cps
Mixing Ratio 1 Part A to 4 Parts B by Volume
Solids Content 40-45%
Volatile Organic Content (VOC) <60 gm/L
Bond Strength to Concrete 400-500 psi (100% concrete failure)
Weight per Gallon 8.75-9.00 pounds per gallon, mixed

CURE/DRY TIME

Pot Life 2-4 hours
Dry to Touch 4-6 hours @ 75°F
Re-Coat 6-24 hours @ 75°F
Light Traffic 24 hours @ 75°F
"H" Hardness 2 days
"5-H" Hardness 30 days

MAINTENANCE

If floors become slippery due to animal fats, oil, grease, or soap film, clean and rinse thoroughly.

Epoxy.com PRODUCT #675 is easily cleaned with neutral soaps or detergents. Routine mechanical scrubbing is recommended for all surfaces having a non-skid texture. Waxing is optional. Long periods of heavy traffic may cause wear patterns necessitating a maintenance application of a finish coat.

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter