[Home] [Catalog of Products] [Where to Start with Epoxy] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Coatings] [Conductive]  [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Injection] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy]  [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Wood Filler] [Who is Epoxy.com] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [MSDS in Acrobat Format] [Online Ordering Authorization Form]

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980  

Epoxy Mortar Adhesive Binder

Lo-Mod Low Viscosity 100% Solids Epoxy

Epoxy Product #10


GENERAL DESCRIPTION

Epoxy Mortar Adhesive Binder - Low Viscosity - Product #10 is a 100% solids Lo-Mod Low Viscosity adhesive used as a binder for epoxy mortar systems in patching and grouting applications, as a seal coat for non-skid surfaces outside, and as a primer to insure high bond strength for coatings and patches. Product #10 Low Modulus Low Viscosity Epoxy Resin Adhesive and Binder System is Zero (0) VOC.

ADVANTAGES

  • Low Modulus, stress relieving
  • Moisture insensitive (cures on damp or wet surfaces)
  • Easily Troweled
  • Withstands movement from thermal change
  • Meets ASTM C-881 Type III, Grade 1 Class B and C standard specification
  • Low Viscosity - Excellent wetting properties
  • Good shock absorption qualities

SURFACE PREPARATION

Surface  to receive  Product #10 Mortar Resin must he clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion, or acid etching. Remove water and dust from all surfaces with an oil-free blast immediately prior to application. See Epoxy.com Surface Preparation Guide for more details.

MIXING INSTRUCTIONS

Temperature of Mortar Adhesive Binder Low Viscosity Product #10  must be 50 degrees F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.

To prepare Product #10 as a mortar, slowly add 3-5 parts by volume of clean, dry, well graded sand to one part by volume of mixed epoxy. Continue to mix until aggregate is thoroughly wetted down.

APPLICATION

Mortar Binder Low Viscosity Product #10  can be applied with a brush, roller or squeegee when used as a primer or seal coat. For skid resistance, broadcast sand at a rate of 2 lbs. per square yard. For mortar applications finish surface with trowel. Prime surface to be patched with neat material.

Use of solvents for thinning Product #10 Low Mod Low Viscosity Adhesive Mortar will prevent proper cure. New concrete must he 28 days old prior to application of Product C10. Temperature of substrate must be above 40 degrees F.

SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

CLEANING INSTRUCTIONS

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent. \

APPLICATION PROPERTIES @77°F

Mix Ratio 2:1 By Volume
Viscosity (mixed) (ASTM D-2393) 400-450 cps
Gel Time (ASTM C-881) 30-40 minutes
Consistency no bead formed
Initial Cure 6-8 Hours
Final Cure 7 Days
Packaging (unit size) 1 gal., 5 gal., drums
Standard Colors neutral, & Colors Listed Below

TENSILE PROPERTIES

Elongation (ASTM D-1652) >10%
Compressive Strength (ASTM D-695) 10,000 P.S.I
Absorption (ASTM D-570) 0.36%
Thermal Compatibility passed test
Adhesion to Concrete (ACI Committee 403) 250 p.s.i (concrete fails)
Shrinkage (ASTM C-883) passed test
Bond Strength (ASTM C-882) 2290 p.s.i (min)
Tensile Strength (ASTM D-790) 3,500 p.s.i min.
Flexural Strength (ASTM D-790) 2,800 p.s.i min.

Color Chart HereClick the picture of color card below  for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter