Epoxy.com Product #495 Urethane Pedistrian Traffic Membrane - For Indoor, Outdoor and Direct Sunlight

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy.com System #495

Elastomeric Urethane Pedestrian Traffic Membrane
For Use Indoor, Outdoor and Direct Sunlight


Elastomeric Polyurethane System Description

Epoxy.com System #495 is an Elastomeric Urethane Membrane System, that is liquid applied.  System #495 Elastomeric Membrane System is seamless, elastomeric (flexible), and UV.  These qualities make it an excellent choice for outside applications in direct sun and weather, where water tightness, durability, and excellent appearance is required. Its elastomeric properties will allow horizontal movements up to 1/8 inch without breaking.

Epoxy.com System #495 has excellent abrasion and chemical resistance.  The surface of System #495 can be varied to achieve the required anti-skid and decorative look.

Elastomeric Polyurethane System Advantages

  • Waterproof
  • Elastomeric
  • Resistant to Sunlight (UV)
  • Safety (Anti-Skid)
  • Epoxy.com System #495 is a system not just a single product so it can be tailored to the specific needs of your application.

Elastomeric Polyurethane System Considerations

  • All control joints must be properly installed, and carried (revealed) to the surface of the system.
  • Substrate must be properly prepared - see Surface Preparation.
  • Substrate temperature should be 60 degrees F. (absolute minimum of 55 degrees F required).  If installation is to made at lower temperature, the material will need a cold temperature cure.
  • On grade or below grade applications must have an effective moisture vapor barrier under the slab.
  • When the substrate has hydrostatic and/or moisture vapor transmission issues they must be treated before the installation of Epoxy.com System #495 Elastomeric Urethane Membrane System.
  • Not for use in California

Typical Uses for the Elastomeric Polyurethane System

Epoxy.com System #495 Elastomeric Urethane Membrane System is ideal for:

  • Raised Walkways
  • Balconies
  • Concrete and Wooden Decks
  • Animal Housing and Cage Wash Areas
  • Coolers
  • Secondary Containment
  • Docks and Ramps
  • Garages laundries
  • Locker Rooms
  • Mechanical Equipment Rooms
  • Pool Decks
  • Showers
  • Utility Rooms
  •  Any flooring/decking application that requires a durable, flexible, waterproof, and attractive flooring/decking.

Technical Data - System Performance Properties

Flammability  ASTM D635 Self Extinguishing
Fungus & Bacteria Growth  Mil-F-52505 § 4.4.2.11 Will not support growth of fungus or bacteria
when subjected to mildew and bacteria tests
Hardness  ASTM D-2240 20-50 Shore D
Bond Strength to Concrete ACI COMM #403, Bulletin 59-43 300psi (100% Concrete Failure)
Resistance to Elevated Temperature Mil-D-3134F § 4.7.4 No slip or flow at required temperature of 158F
Coefficient of Friction ASTM D-2047 0.60
Water Absorption ASTM D-570 Nil
Thermal Shock Resistance ASTM C-884 Passed
Abrasion Resistance ASTM D-4060 Will vary with finish
Impact Resistance Mil-D-3134F  § 4.7.3 Withstands 16 ft./lbs. without cracking, chipping or
delamination.
Compressive Strength ASTM C-579, 7 days 5000 psi
Tensile Strength ASTM C-307 1,200-1,500
Thermal Coefficient of Expansion ASTM C-531 12-15 x 10-6

Membrane Performance Properties

Ultimate Tensile Strength ASTM D-638 1,000-1,200 psi
Tensile Elongation ASTM D-638 350-400%
Hardness ASTM D-2250 80 Shore A

Elastomeric Polyurethane Systems Maintenance

Clean with neutral soaps or detergents. Anti-skid floors typically use periodic mechanical cleaning. Long period of heavy traffic may cause wear patterns requiring a maintenance of  the finish coat.

Elastomeric Polyurethane System Application

Typical system components and application rates are as follows:

  1. Epoxy.com Product #899 Primer applied at a rate of 250-300 SF per gallon
  2. Epoxy.com Product #459 applied at a rate of 50 SF per gallon (1st coat)
  3. Epoxy.com Product #459 applied at a rate of 50 SF per gallon (2nd coat)
  4. Epoxy.com Product #77 broadcast into the wet send coat of Product #459 at a rate of 1/2 lb per square foot
  5. Epoxy.com Product #467 applied in 2 coats at a rate of 200 square feet per gallon per coat

For a complete set of installation instructions see Elastomeric Decking System #495 Installation Guide or contact Epoxy.com Technical Support Department.

 Skip Navigation Links

Epoxy.com Home PageExpand Epoxy.com Home Page

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/