Epoxy.com Product #459
Polyurethane Flexible Membrane
Epoxy.com Product #459 is a two component, high solids,
elastomeric urethane used in waterproofing applications.Epoxy.com
exhibits excellent elongation properties along with high tensile
strength and tear resistance to make it an ideal crack resistant
membrane for use under other Epoxy.com flooring systems.
Epoxy.com Product #459 is also used with
Epoxy.com Elastomeric Systems.
- Bridges Hairline Cracks
- Resistant to Automotive Fluids
- Quick Cure Time
- One Coat Application
- Low Odor
Epoxy.com Product #459
is packaged with 41.5 pounds of Part A in a 6-gallon pail and 6
pounds of Part B in a gallon can to make a convenient 5-gallon unit.
- Slabs on Grade Must Have an Efficient Vapor/Moisture Barrier
- Substrate Must be Free of Curing Agents and Other Foreign Materials\
- Minimum Application Temperature of 50ºF
- Proper Respiratory Equipment Must Be Used When Required
- Do Not Apply Epoxy.com Product #459 to Wet or Damp Surfaces
|Mix Ratio |
|6.6 parts A - 1 part B
100 parts A - 13 parts B
|Solids Content, by volume
|Weight per Gallon, mixed
||30 mins @ 77ºF, 50% RH
||6 - 8 Hours
|Tensile Strength ASTM-D-412
|Ultimate Elongation ASTM-D-412
|Adhesion (unprimed) ASTM-D-904
|Hardness Shore A ASTM-D-2240
|Impact Resistance ASTM-D-2794
||160 In. lb.
Prepare surface in accordance with Epoxy.com Surface Preparation
Guide New concrete must be cured at least 30 days. All concrete curing
compound must be mechanically removed, along with any foreign
material. Old concrete must be structurally sound and prepped according
Prime where necessary with Epoxy.com Product #899 Primer. Mix two (2)
Parts A and one (1) Part B by volume with low speed drill for two
minutes minimum. Apply with squeegee, brush, or roller. Do not puddle.
Spread rate is approximately 250sq.ft./gallon.
Mix 6.6 Parts A to one (1) Part B by volume or 100 Parts A to 13
Parts B by weight using a low speed drill for 3 - 5 minutes. Epoxy.com
Product #459 can be applied by using a roller, air brush, spray, or
notched squeegee at a rate of 50 to 55 square feet per gallon to yield
28 to 30 dry mils.
Clean tools with xylene or lacquer thinner.
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Since 1980 - Over 33 years
Florida & Vermont
Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2014 (providing online information about the
right product for the right job for 20 years) EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a division of Epoxy Systems, Inc. (hereinafter known as
"Supplier" warrants its products (when properly stored) for the period of
time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylates
and Polyurethanes Six (6) months. Supplier warrants that its products
will be free of manufacturing defects and will be in conformity with
published specifications when handled, stored, mixed and applied in
accordance with recommendations of Supplier. If any product fails to meet
this warranty, the liability of Supplier will be limited to replacement of
any non-conforming material if notice of such non-conformity is given to
Supplier within the warranty period for the material (as indicated above),
or within 1 year of the delivery of materials (whichever is sooner).
Supplier may in its discretion refund the price received by Supplier in lieu
of replacing the material. No customer, distributor, or representative of
Supplier is authorized to change or modify the published specifications of
this warranty in any way. No one is authorized to make oral warranties on
behalf of Supplier. In order to obtain replacement or refund the customer
must provide written notice containing full details of the non-conformity.
Supplier reserves the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S
OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN
ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR
LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. All quotes and sales subject to availability.
Many of our products are
on an individual order basis. Unless authorized by us
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Novolac] [Primers Sealers]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]