Epoxy.com Product #215 LVOC
High Solids Low VOC Coating.
DESCRIPTION:
EPOXY.COM #215 LVOC Epoxy Protective Coating
is a two-component, high solids epoxy coating. The material components are
Epoxy and high performance polyamide with corrosion inhibitors. It is 100 %
reactive. It has a convenient 1:1 mixing ratio by volume and a long pot life
to simplify mixing and application.
ADVANTAGES:
When cured,
EPOXY.COM #215 LVOC provides a tough, tile-like finish with good
flexibility. It protects concrete, steel, or wood against attack by salts,
acids and alkalizes and some solvents
PHYSICAL PROPERTIES:
|
| Color |
Gray |
|
Mix Ratio |
1:1 by volume |
|
Volume Solids |
68% |
|
Pot Life |
4 hours
|
|
Min recoat with self |
4 hours |
|
Max recoat with self
|
7 days |
|
Min recoat w/polyurethane
|
12 hours |
|
Max recoat w/polyurethane |
7 days |
|
Weight per gallon
|
13.5 lbs. |
|
Viscosity |
3,000 cps
|
|
Drying time at 70°F |
|
|
To touch |
5 hours |
|
To recoat |
14 hours
|
|
Full cure |
7 days |
|
V. O. C. Content |
3.2 lbs / gallon |
|
Shelf Life |
|
|
Unmixed closed
container |
12 months
|
SURFACE PREPARATION:
STEEL SURFACES:
New steel surfaces should be initially blasted to near-white metal surface
cleanliness in accordance with SSPC-SP10 for immersion surface or commercial
blast cleanliness in accordance with SSPC-SP6 for non-immersion service.
Blast profile on steel should be 1.5-2.0 mils in depth and be of a sharp,
jagged nature as opposed to “peen” pattern. May be used as an intermediate
or finish coat over Epoxy.com #1200
Zinc Rich Primer.
CONCRETE SURFACES:
New concrete shall be cured a minimum of 30 days. Concrete surfaces shall be
clean, sound and dry. Abrasive blast to remove curing compounds, existing coatings or laitance prior to
application on concrete floors
MIXING:
Combine (1) one part by volume of Component "A" with (1) one part by volume of Component
"B" Mix for a minimum of (3) minutes
with a low speed electric drill and a
Mixing Paddle.
No induction time is needed
before applying.
APPLICATION:
EPOXY.COM #215 LVOC Epoxy Protective Coating
may be applied by brush, roller or spray. All spray equipment must employ traps to prevent water and oil from
contaminating coating.
COVERAGE:
Typical application
is 160 sq. ft. per gallon; film thickness will be approximately ten (10)
mils wet and eight (8) mils dry.
Two coats are recommended.
PACKAGING:
2 gallon and 10 gallon units.
CAUTION:
“A” Component contains epoxy resin.
DANGER! “B” Component contains alkaline amines; strong sensitizer. May
cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or
sprayed. Prevent all contact with
skin or eyes. Wear protective
clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.
FIRST AID: In case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for
at least fifteen (15) minutes.
Remove contaminated clothing and shoes.If irritation persists, seek medical attention.Wash clothing before reuse.
FOR INDUSTRIAL USE ONLY / KEEP AWAY FROM CHILDREN