|
|
|
EpoxySystems' Product #1004 Self Leveling Floor Topping DESCRIPTION EPOXYSYSTEMS’ PRODUCT #1004 Self-Leveling Floor Topping is a one component copolymer modified cementitious topping. EPOXYSYSTEMS’ PRODUCT #1004 is ready to use with only the addition of clean water to activate the polymer modified cement topping. EPOXYSYSTEMS’ PRODUCT #1004 has a special blend of plasticizers to provide zero shrinkage, high flow and bonding properties necessary for floor topping.ADVANTAGES
USES: Architectural floor topping for a variety of floor finishes; such as: tiles coatings, carpeting, rubber and vinyl sheeting, requiring a smooth substrate.
SURFACE PREPARATION CONCRETE SURFACE: Concrete surfaces shall be cleaned to remove dirt, curing compounds, existing coatings or laitance to provide a clean, sound bonding surface. Cleaning may be accomplished with EpoxySystems’ Masonry Cleaner and water blasting, acid etching and water blasting, sandblasting, or other methods that would achieve a similar result.PRIMING: Prime the surface with EpoxySystems’ Product #825 Floor Sealer prior to placement of the topping or repair. The advantage of a primer is to prevent air release from the subfloor rising and forming bubbles and pinholes on the surface of the EPOXYSYSTEMS’ PRODUCT #1004 Self-Leveling Floor Topping. The prime coat is mixed at a ratio of (1) gallon (3.79L) EpoxySystems’ #825 Floor Sealer with (2) gallons (7.57 L) clean potable water and spread by brush or roller at a rate of 200-300 square feet (18.58 m2 -27.87 m2) per gallon. Apply topping material while EpoxySystems’ #825 Floor Sealer is tacky. If the prime coat drys prior to the placement of the EPOXYSYSTEMS’ PRODUCT #1004, apply a second coat of primer.MIXING: Mixing should be accomplished with a slow speed drill and EpoxySystems’ Mixing Paddle. Each 55 lb (24.95 Kilo) bag of EPOXYSYSTEMS’ PRODUCT #1004 requires the addition of 6.8 to 7.25 quarts (217 - 232 oz.) (6.44 - 6.44 L) of cool, clean water to produce a free flowing, self-leveling consistency. Measure out water and add to mixing container. Add EPOXYSYSTEMS’ PRODUCT #1004 Powder while mixing. Mix the material for three minutes. When using drill type mixer, keep the mixing head well down in the liquid to avoid any entrapment of air. Do not mix for more than five minutes. For thickness over 1/2", EPOXYSYSTEMS’ PRODUCT #1004 can be extended with EpoxySystems’ Product #75 Filler in equal portions. Do not add extra water.
APPLICATION Pour mixed material onto primed substrate and spread with squeegee or trowel and allow to self-level. Any high spots can be pared off with the edge of a trowel after initial set. The required thickness must be achieved in one application. For best results, pouring and leveling should be continuous until area is completely leveled. PACKAGING EPOXYSYSTEMS’ PRODUCT #1004 is packaged in 55 lb. (24.95 Kilo) bags and yields approximately 0.50 cubic feet. When placed at an approximate 1/4" thickness, EPOXYSYSTEMS’ PRODUCT #1004 will cover 24 square feet. (2.23 m2) LIMITATIONS Working time is approximately 20 minutes at 70o F (21.1NC) . Higher temperatures reduce the work time. If mix stiffens, it should be discarded. On-grade slabs must have a damp proof membrane in the subfloor. Surface should be cool before applying EPOXYSYSTEMS’ PRODUCT #1004. Do not use below 40o F (4.4NC) . EPOXYSYSTEMS’ PRODUCT #1004 should be protected from direct sunlight and strong wind for 2 - 4 hours. YIELD EPOXYSYSTEMS’ PRODUCT #1004 produces 0.50 cubic feet covering approximately 24 square feet at 1/4" thick. Material is packaged in 55 lb. (24.95 Kilo) bags.CAUTION Contains Portland Cement and Silica. Avoid breathing dust. Cement powder or freshly mixed concrete, grout or mortar may cause skin injury. Avoid contact with skin; wash exposed areas promptly with water. If any cement powder or mixture gets into eyes, rinse immediately and repeatedly with water. Get prompt medical attention!FOR INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
