|
Epoxy.com Product #825 Polymer Floor Sealer and Primer
DESCRIPTION Epoxy.com Product #825 Floor Sealer is a non-rewettable, polymer emulsion formulated for use with fast or normal setting floor underlayments. It is zero VOCs (volatile organic compounds) making safer for the user and for the environment. WHERE TO USE Epoxy.com Product #825 Floor Sealer is used as a primer to seal concrete, wood or other porous substrates prior to installation of underlayment, preventing excessive water loss from the underlayment before setting occurs. Epoxy.com Product #825 Floor Sealer is used as a primer to promote adhesion of underlayment to existing substrate. Epoxy.com Product #825 Floor Sealer is used as a primer to seal and strengthen the surface of the in-place underlayment before flooring adhesives are applied. APPLICATION Seal Porous Substrates Dilute one (1) part Epoxy.com Product #825 Floor Sealer with two (2) parts clean, potable water. Apply to clean surfaces by brush, roller or spray, at a rate of approximately 200 square feet per diluted gallon. After sealer dries, promote adhesion with Epoxy.com PRODUCT #1100 Rewettable Adhesion Promoter. Promote Adhesion To Existing Substrate Strengthen Surface of Freshly Place Underlayments If underlayment is allowed to dry, soak with water prior to applying Epoxy.com Product #825 Floor Sealer. If soaking is not possible, dilute one (1) part Epoxy.com Product #825 Floor Sealer with two (2) parts clean, potable water and apply at a rate of approximately 200 square feet per diluted gallon. It is highly recommended that the diluted material not be stored for future use. Dilute Epoxy.com Product #825 Floor Sealer as needed for the particular area and amount to be used. Tools and application equipment can be cleaned with soap and water. Soap residue should be thoroughly rinsed from equipment prior to the next use. CAUTION WARNING! Skin and eye contact with material may cause slight irritation. Ingestion may cause gastric disturbance. Avoid contact with eyes, skin and clothing. Wear protective clothing if splashing occurs. Provide adaequate ventilation or respiratory protection if vapor or mist is created. Post "Slippery When Wet" signs where appropriate. FIRST AID In case of eye contact, immediately flush eyes with water for 15 minutes. If irritation develops, consult a physician. In case of skin contact, wash affected areas with soap and water. Remove and wash contaminated clothing before reuse. If irritation develops, consult a physician. If swallowed, dilute with water. Decision to induce vomiting should be made only by a physician. Never give fluids or induce vomiting if the victim is unconscious. Get immediate medical attention. FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN. |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
