Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Chemical Resistant Polyurethane Maintance Coating

Excellent UV and Chemical Resistance

Epoxy.com Product #402


GENERAL DESCRIPTION

Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating is a two component chemical resistant polyurethane coating. The high gloss finish offers excellent abrasion resistance, chemical and stain resistance, and color retention.

Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating can be used equally well on vertical or horizontal surfaces. It is ideal for concrete floors and walls in warehouses, storage facilities, aircraft hangers, animal housing, and vehicle maintenance facilities.

Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating is not for use in California

ADVANTAGES

  • Excellent Abrasion Resistance
  • Excellent Chemical Resistance
  • UV Resistant - means a long life even in direct sunlight
  • Excellent Color Stability - Pigmented Version
  • Clear Version Resists Ambering Even in the Brightest Sunlight
  • Exterior and Interior Uses
  • May be used on both Horizontal and Vertical Applications
Epoxy.com Product #402 over Epoxy.com Chip Flooring

Epoxy.com Product #402 Clear
Over Chip Flooring - Over Basement Room
Picture Courtesy of Matt Dekman
Used with Permission - All Rights Reserved

SURFACE PREPARATION

Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast immediately prior to application.

APPLICATION

Prime: For best bond to properly prepared surface, use Epoxy.com Product #899 Primer.

Body: Apply Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating with brush, roller (short napped), or squeegee followed with back rolling to get recommended thickness (3 mils DFT).

Finish: Apply top coat as required (minimum 3 mils DFT).

Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating is also available in the following forms:

  • As a slip or skid resistant finish using a non-skid additive in the finish.
  • As an electrostatic dissipating finish version - Epoxy.com Product #675

LIMITATIONS

Epoxy.com Product #402 over Epoxy.com Chip Flooring

Epoxy.com Product #402 Clear
Over Chip Flooring - On Outside Patio
Picture Courtesy of AA Permacoat
Used with Permission - All Rights Reserved

Surface  to receive Epoxy.com PRODUCT #402 Chemical Resistant Polyurethane Coating must be dry. Minimum application temperature of 40°F (Contact Epoxy.com Technical Support for Low Temperature Cure). Maximum application temperature of 100°F. Avoid applications on surfaces without effective vapor barriers.

SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

CLEANING

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.

Physical Properties

Color Standard colors for this product are:
Clear (satin and gloss), White #001,
Light Gray #100, White Sand #210,
Taupe #300,Mocha #400, Caramel #420,
& Brick Red #900.
Gloss, 60°F 85-100
Mix Ratio     2Ato 1B by volume
Pot Life 30-40 minutes @ 70°F
VOC 405 gm/liter
Solids Content, % volume    56.0
Coverage 300 ft2/gal @ 3 mils DFT

DRY TIME

10-20 mil film 1O~14 hrs
Light Traffic 16 hrs
Ultimate Cure @ 74°F
                     @50°F
5 days
14davs

CHEMICAL RESISTANCE

REAGENT

Rating

REAGENT

Rating

Acetic Acid-5% L Iodine R
Acetone L Lactic Acid-15% R
Betadine R Methyl Ethyl Ketone L
Bleach L Nitric Acid-10% R
Citric Acid-30% R Skydrol R
Crude Oil R Sodium Hydroxid-50% R
Diesel Fuel R Sulfuric Acid-20% R
Ethylene Glycol R Toluene R
Fafty Acids L Urea R
Gasoline R Vinegar L
Hydrochloric Acid-15% R Xylene R
R= Recommended for continuous Service
L=Limited recommendation, occasional spills

PERFORMANCE PROPERTIES

Adhesion to concrete ACI Committee 403 200 psi (concrete fails)
Abrasion Resistance ASTM-C501 30-40 mg loss
     (CS-17 wheel, 1 kg load, 1000 cycles)
Service Temperature MIL- D-3134F 160°F (immersion) 250°F (dry heat)
Impact Resistance MTI-D-3134F § 4.7.5 Withstands 16ft./lbs. no cracking, delamination or chipping
Elevated Temperature Resistance MIL-D-3134F § 4.7.3   No slip or flow at required temperatures at 158°F
Water Absorption (24. hr. immersion) ASTM-D-670-63 0.10% maximum
Hardness ASTM D3363 2H±
Color Chart HereStandard colors for this product are: White #001, Light Gray #100, White Sand #210, Taupe #300, Mocha #400, Caramel #420, & Brick Red #900.  The other colors listed to the left are available on on orders of 30 gallons or more.

Click the picture of color card below  for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

BLOG POSTS & NEWS

You can find more information on Polyurethane Products, and many of our other products at news.epoxy.com.

Download this file in Adobe Acrobat  format for formal presentation.

 Skip Navigation Links

Epoxy.com Home PageExpand Epoxy.com Home Page

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2015 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/