Epoxy.com Product #831
Moisture Tolerant Epoxy Primer
For Use Under Epoxy, Polyurethane and Polyurea
100% Solids, 0 (Zero VOC) Primer - Meets Strictest Low VOC Standards
Epoxy.com Product #831 Moisture Tolerant Epoxy Primer is a two-
component, 100% solids VOC compliant primer for
concrete. Product #831 can be applied directly over wet
concrete, at temperatures as low as 35° F. The low
viscosity, no induction time and long pot life
simplify application. Product #831 protects by
penetrating concrete or wood and has excellent
adhesion to damp concrete and other materials. It
is suitable for many topcoats including epoxy,
polyurethane and polyurea.
Epoxy.com Product #831 Moisture Tolerant Epoxy Primer is Zero (0)
VOC. Since Epoxy.com Product #831 Moisture Tolerant Epoxy Primer
has no VOC content, it complies with even the strictest low VOC
|Weight per gallon|| 8.8|
|Solids, Volume|| 100% |
|Viscosity|| 1100 ± 250 cps|
|Shelf Life - closed container|| 24 months min.|
|Pot Life @ 70°F || 1 hours|
|Drying time at 70°F to touch|| 3 hours|
|Through dry @ 70°F|| 16 hours|
|Drying time at 40°F to touch|| 4 hours|
|Through dry @ 40°F|| 2 days|
|Min Recoat @ 70° w/epoxy polyurethane and polyurea||6 hrs.|
|Max Recoat @ 70°F w/epoxy polyurethane and polyurea || 6 days|
|VOC|| 0.1.Lbs/ gallon|
|Flash Point Tag Closed Cup|
|Part A|| <230° F (24 °C)|
|Part B|| <200° F (31° C)|
Concrete surfaces shall be cleaned to remove dirt, grease, oils, curing
compounds, hardening agents, existing coatings or
laitance to provide a clean, sound bonding
surface. Cleaning may be accomplished with waterblasting, abrasive cleaning, acid
etching followed by abrasive cleaning, shot-blasting, sandblasting, or
other methods that achieve a similar result. See
Epoxy.com Surface Preparation Procedures
for more details.
Combine two parts Epoxy.com Product #831 Moisture Tolerant Epoxy Primer by volume of "A" with one
part by volume of "B" (mixing ratio 2A:1B). Mix
for not less than three minutes, using a slow
speed drill, (300 to 600 rpm) and a Epoxy.com-Mixing
Paddle. When mixing has been completed,
apply immediately no induction time is
Epoxy.com Product #831 Moisture Tolerant Epoxy Primer may be applied by brush, roller or
spray. All spray equipment must employ traps
to prevent water and oil from contaminating
Epoxy.com Product #831 Moisture Tolerant Epoxy Primer will cover approximately 200 sq. ft./gal./coat at 8.0 mils DFT, dependent upon surface texture. Minimum DFT is recommended
is 5 mils. Maximum DFT is recommended at 15 mils.
Epoxy.com Product #831 Moisture Tolerant Epoxy Primer is packaged in three (3) gallon and fifteen (15) gallon units.
Epoxy.com Product #831 Moisture Tolerant Epoxy Primer "A" Component contains epoxy resin.
DANGER! Epoxy.com Product #831 Moisture Tolerant Epoxy Primer “B” Component contains alkaline amines; strong sensitizer.
May cause skin sensitization or other allergic responses.
Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes.
Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.
In case of skin contact, immediately wash with soap and water.
In case of eye contact, flush eyes with copious amounts of water
for at least fifteen (15) minutes. Remove contaminated clothing shoes. If irritation persists, seek medical attention. Wash clothing before reuse.
Read MSDS and Technical Data Sheets before using
KEEP AWAY FROM CHILDREN
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]