Epoxy.com Product #661
Vinyl Ester Novolac Binder
Epoxy.com Product VINYL ESTER BINDER is a clear, 100% reactive, vinyl ester novolac used to coat or line concrete or
steel surfaces in chemically aggressive industrial environments. It is used for coating primary and
secondary containment, trenches, troughs, pump pads, and equipment.
- Excellent resistance to a wide range of chemicals.
- High temperature performance; in many cases up to 350°F (spills) or 400°F (dry heat).
- Application by conventional painting techniques.
- Best overall performance coating for secondary containment.
- Self-extinguishing in thin films.
- Substrate temperature must be a minimum of 50°F.
- Substrate must be free of dirt, waxes, curing agents, and other foreign materials.
- Substrate must be completely dry.
- Requires skilled installers to assure successful results.
Two-component peroxide cured vinyl ester novolac.
Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared as outlined in
Epoxy.com Surface Preparation Guide
Observe all precautions on MSDS and label when using this product. Mix 3-4 oz. Part B per gallon with
Part A with a low speed drill for at least two (2)minutes. For spray application, add up to 1 quart
Styrene per mixed gallon, if needed.
Apply by roller, brush, or spray. Use a nylon or natural bristle brush or a good quality medium nap roller. Can
be sprayed with airless or conventional spray.
Clean skin with soap and water; use MEK, xylene, or clean proprietary epoxy thinners for equipment.
160 square feet per gallon yields 8 mils DFT due to shrinkage during cure. Two coats are recommended for general service, as a coating.
Epoxy.com Vinyl Ester Binder is available in Clear.
Typical Performance Properties
|Tensile Strength||ASTM D-638||11,000 psi|
|Adhesion to Metal||ASTM D-638||2,500 psi|
|Adhesion to Concrete||ACI COMM #403||350 psi (concrete fails)|
|Hardness||ASTM D-2240||85 (Shore D)|
|Abrasion Resistance||ASTM 4060||26-28 mg. loss (CS-17 wheel, |
1 kg load,1000 cycles)
|Service Temperature||320°deg;F (immersion)||400°F (dry heat)|
|Gloss; 60°||High Gloss|
|Weight/Gallon||8.7 lbs., mixed|
|Mix Ratio||32A:1B by volume|
|Pot Life||45 min. @ 75°F (3 gallon kit)|
|Viscosity||600 cps, mixed approx.|
|Shelf Life||2 months, maximum|
|Re-Coat||5-8 hours @ 70°F*|
|Foot Traffic||8-12 hours|
|Full Chemical||Cure 3-5 days|
|*Shorter recoat times affect gloss.|
|Acetic Acid-75%|| R|
|Acetone || L|
|Acrylic Acid-25%|| R|
|Citric Acid|| R|
|Chromic Acid-20%|| R|
|Diesel Fuel|| R|
|Ethylene Glycol|| R|
|Fatty Acids|| R|
|Hydrochloric Acid-37%|| R|
|Lactic Acid|| R|
|Methyl Ethyl Ketone||L|
|Nitric Acid-50%|| R|
|Sodium Hydroxide-50%|| R|
|Sulfuric Acid-70%|| R|
|R-Recommended for continuous service.|
L-Limited Recommendation, occasional spills.
*-May cause slight stain or discoloration.
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2014 (providing online information about the
right product for the right job for 20 years) EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a division of Epoxy Systems, Inc. (hereinafter known as
"Supplier" warrants its products (when properly stored) for the period of
time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylates
and Polyurethanes Six (6) months. Supplier warrants that its products
will be free of manufacturing defects and will be in conformity with
published specifications when handled, stored, mixed and applied in
accordance with recommendations of Supplier. If any product fails to meet
this warranty, the liability of Supplier will be limited to replacement of
any non-conforming material if notice of such non-conformity is given to
Supplier within the warranty period for the material (as indicated above),
or within 1 year of the delivery of materials (whichever is sooner).
Supplier may in its discretion refund the price received by Supplier in lieu
of replacing the material. No customer, distributor, or representative of
Supplier is authorized to change or modify the published specifications of
this warranty in any way. No one is authorized to make oral warranties on
behalf of Supplier. In order to obtain replacement or refund the customer
must provide written notice containing full details of the non-conformity.
Supplier reserves the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S
OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN
ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR
LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. All quotes and sales subject to availability.
Many of our products are made
on an individual order basis. Unless authorized by us
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Novolac] [Primers Sealers]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]