Epoxy.com Product #115
Epoxy System for Modifying Concrete
DESCRIPTION
Epoxy.com Product #115
Epoxy System for modifying concrete is a two component, 2:1 ratio, 100% solids, liquid epoxy
resin system. It can be added to
conventional concrete or mortar mixes to produce high strength, epoxy modified
concrete or mortar mix.
WHERE TO USE
Especially suitable for topping for bridge decks, bridge seats, parking garages,
piers, grade slabs, and pads for rail or machine setting.
ADVANTAGES
Epoxy.com Product #115
Epoxy System for modifying concrete will increase durability, freeze-thaw and impact resistance.
Epoxy.com Product #115
will increase compressive, flexural, tensile and
tensile splitting strengths. The
coefficient of expansion and set time is the same as normal concrete.
SURFACE PREPARATION
Substrate must be clean and sound.
ABOVE GRADE - Apply Product #7 Bonding
Agent to the surface to be repaired at a rate of approximately 100 square
feet / gallon. While the bonding agent is still tacky, place the epoxy modified mortar or concrete mix.
GRADE SLAB
- Apply a slurry coat of epoxy modified mortar to
the area to be repaired. Place the
epoxy modified mortar or concrete while the slurry is still wet.
MIXING
The following mixes are suggested as guides. Local aggregates vary, mix proportions should be based on available
supply. Mix with as low a water
content as is consistent with proper placing and consolidation.
RECOMMENDED
PROPORTIONING FOR EPOXY MODIFIED MORTAR:
|
Type I Cement
|
1 bag (94 lbs) |
Purchased by Installer locally |
|
Sand
|
300 lbs |
Purchased by installer locally |
|
Product #115
|
2 gallon |
From Epoxy.com |
|
Water
|
5.5 gallons (approx) |
Tap Water |
Mix epoxy and portland mortar separately, then combine.
RECOMMENDED
PROPORTIONING FOR EPOXY MODIFIED CONCRETE
|
Type I Cement
|
1 bag (94 lbs) |
Purchased by installer locally |
|
Sand
|
300 lbs |
Purchased by installer locally |
|
3/8" Pea Gravel
|
163 lbs |
Purchased by installer locally |
|
Product #115
|
2 gallon |
From Epoxy.com |
For epoxy modified concrete, it is not necessary to
pre-mix epoxy. Place Coarse Aggregate in
concrete mixer, add all of each component of
Product #115 (A & B). Mix
for (3) three minutes. Add sand, some
water, then cement. Continue mixing until
well blended. Add water to obtain desired
slump. (Water requirement will vary
depending on moisture in sand).
For still better physical properties use Epoxy.com Product
#115 Part "C" for your aggregate.
CLEAN UP
Flush equipment frequently with water. Tools in
contact with neat epoxy must be cleaned with
MEK, Xylene or other solvent-type cleaner. Tools in contact with concrete and mortar may be washed with water.
LIMITATIONS
Not recommended for use at temperatures below 50°F. Keep material between 65°F and 85°F during mixing. Do not mix
Product #115 with organic solvents.
STORAGE -Keep in cool dry area.
SHELF LIFE - 1 year
CAUTION
A
COMPONENT - FOR INDUSTRIAL USE ONLY!! WARNING!! May
cause skin sensitization or other allergic responses. Avoid inhalation of vapor.
Use good ventilation particularly if material is heated or sprayed. Prevent all contact with skin or eyes. If contact with skin occurs, wash immediately with soap and water. In case of contact with eyes, flush immediately with water and contact a
physician. SPI Class 3.
B COMPONENT - DANGER!!
CAUSES SEVERE BURNS!! Contains alkaline amines; strong sensitizer. Do not get into eyes, on skin, or clothing. Avoid breathing vapor. Keep
container closed. Use with adequate
ventilation. Wash thoroughly after
handling.
FIRST AID: In case of contact, immediately flush eyes or skin
with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Call a physician. Wash clothing before reuse. Discard contaminated shoes.
MCA.
WEAR PROTECTIVE
CLOTHING, GOGGLES, GLOVES, AND/OR BARRIER CREAMS.
|