|
|
Epoxy.com™ Product #115 Epoxy System for Modifying ConcreteDESCRIPTION Epoxy.com Product #115
Epoxy System
for modifying concrete is a two component, 2:1 ratio, 100% solids, liquid epoxy
resin system. It can be added to
conventional concrete or mortar mixes to produce high strength, epoxy modified
concrete or mortar mix. WHERE TO USE
Especially suitable for topping for bridge decks, bridge seats, parking garages,
piers, grade slabs, and pads for rail or machine setting. ADVANTAGES Epoxy.com Product #115
Epoxy System
System for modifying
concrete will increase durability, freeze-thaw and impact resistance.
Product #115
will increase compressive, flexural, tensile and
tensile splitting strengths. The
coefficient of expansion and set time is the same as normal concrete.
SURFACE PREPARATION
Substrate must be
clean and sound.
ABOVE GRADE- Apply
Product #7 Bonding
Agent to the surface to be repaired at a rate of approximately 100 square
feet / gallon. While the bonding
agent is still tacky, place the epoxy modified mortar or concrete mix.
GRADE SLAB
- Apply a slurry coat of epoxy modified mortar to
the area to be repaired. Place the
epoxy modified mortar or concrete while the slurry is still wet.
The following mixes are suggested as guides.
Local aggregates vary, mix proportions should be based on available
supply. Mix with as low a water
content as is consistent with proper placing and consolidation.
RECOMMENDED
PROPORTIONING FOR EPOXY MODIFIED MORTAR:
Mix epoxy and portland mortar separately, then combine.
RECOMMENDED
PROPORTIONING FOR EPOXY MODIFIED CONCRETE
For still better physical properties use Epoxy.com Product #115 Part "C" for your aggregate.
Flush equipment frequently with water. Tools in
contact with neat epoxy must be cleaned with
MEK, Xylene or other solvent-type cleaner.
Tools in contact with concrete and mortar may be washed with water.
Not recommended for use at temperatures below 50°F.
Keep material between 65°F and 85°F during mixing.
Do not mix
Product #115 with organic solvents. SHELF LIFE - 1 year CAUTION
A
COMPONENT - FOR INDUSTRIAL USE ONLY!!
WARNING!! May
cause skin sensitization or other allergic responses.
Avoid inhalation of vapor.
Use good ventilation particularly if material is heated or sprayed.
Prevent all contact with skin or eyes.
If contact with skin occurs, wash immediately with soap and water.
In case of contact with eyes, flush immediately with water and contact a
physician. SPI Class 3.
B COMPONENT - DANGER!!
CAUSES SEVERE BURNS!!
Contains alkaline amines; strong sensitizer.
Do not get into eyes, on skin, or clothing.
Avoid breathing vapor. Keep
container closed. Use with adequate
ventilation. Wash thoroughly after
handling.
FIRST AID: In case of contact, immediately flush eyes or skin
with plenty of water for at least 15 minutes.
Remove contaminated clothing and shoes.
Call a physician. Wash clothing before reuse.
Discard contaminated shoes.
MCA.
WEAR PROTECTIVE
CLOTHING, GOGGLES, GLOVES, AND/OR BARRIER CREAMS.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
