Epoxy.com Product #844
This Product Replaced
by Epoxy.com Product #899
For Refererance Only: This product has been replace by Epoxy.com
Product #844 Concrete Membrane Deck Primer is a 100% solids, two (2)
component polyurethane primer. This thin film primer promotes long term wear
and superior adhesion of the Product #409 Resilient Traffic Bearing Membrane.
The Product #844 penetrates and seals the surface to allow for a smoother,
pinhole free application.
WHERE TO USES:
Product #844 is used only on concrete. May be applied to properly
prepared interior and exterior concrete to enhance the bond and performance
of the Product #409 System.
- 100% Solids
- Zero VOC
- Ease of application
- Eliminates blisters and pinholes
- Fast cure, ready to accept overcoat in 2 hours
- 1:1 Mix Ratio
Pedestrian Grade and Traffic Grade - For pedestrian grade
or traffic grade application apply one coat of Product #844 at 3.0 to 4.0
mils WFT to achieve 3.0 to 4.0 mils DFT. It is recommended that while wet,
the Product #844 be lightly seeded with a rounded 16 / 30 silica sand.
Please refer to Product #409 Resilient Traffic Bearing Membrane Product
data sheet for the complete system description for over coating the
Dry to touch
1 hr @ 70°F
Dry to recoat
2 hrs @ 70°F
Maximum recoat interval of Product #844 when over coated with
Product #409 shall not exceed 36 hours. If maximum over coat is
exceeded reapply Product #844 over a clean dry surface.
Shore D Hardness
MVT, perms at 30 mils dry
Concrete - All concrete must be cured a minimum of 28 days. All
concrete must be clean, sound, dry, free of oils and other bond inhibiting
contaminants. Air and substrate temperature shall be 40°F and rising.
Mechanical surface preparation such as shot blasting, abrasive blasting or
hydroblasting is required to produce a clean and lightly profiled or
textured surface. If hydroblasting is used, allow 24 to 48 hours for
concrete to dry thoroughly.
Combine one (1) part component "A" and one (l) part component "B" by
volume, in the quantity desired. Mix Product #844 with a mixing paddle and
low speed drill for two (2) minutes. Avoid entrapping air while mixing.
Apply immediately after mixing.
Apply by brush, roller, or airless sprayer at 3.0 to 4.0 mils WFT to
achieve 3.0 to 4.0 mils DFT. While Product #844 is still wet, lightly seed
with a rounded 16 / 30 silica sand. Allow to dry a minimum two (2) to four
(4) hours at 70°F or until tack free prior to application of
Product #409 Intermediate coat.
Minimum application temperature of 40°F and rising. Do not apply over
damp or wet concrete. Do not apply to surfaces with active moisture vapor
transmission. Product #409 Intermediate must be applied within 36 hours
after application of Product #844 Primer.
Product #844 is packaged as a 2 gallon and 10 gallon unit.
Product #844 shall be stored in a dry, protected area at temperatures
between 60°F and 90°F. Do not allow to freeze.
Product #844 contains organic isocyanates MDI. Avoid breathing vapors.
Avoid contact with skin and eyes. Do not ingest. Keep away from foodstuffs
and wash thoroughly before smoking or eating. Should skin contact occur,
wash skin well with soap and water. Should eye contact occur, flush
thoroughly for at least 15 minutes with water. Get medical attention.
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Novolac Epoxy] [Primers Sealers]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]