Epoxy.com Product #647 Heat Resistant Epoxy
Epoxy.com Product #647 Heat Resistant Epoxy is a two component highly
cross-linked novolac epoxy resin system. Epoxy.com Product #647 is
especially formulated to be used as a high temperature potting or laminating
resin. It is used to protect parts from high temperatures and corrosion.
Epoxy.com Product #647 is 100% solids and has a convenient 2:1 by volume mix
ratio and is easy to apply.
- Stable up to 400°F
- High chemical resistance to acids, alkalies and other chemicals
- Low viscosity allows penetration into fiberglass fabric to make high
- Low viscosity allows filler loading for high temp epoxy potting
- Steel and Concrete Protective Surface where high temperatures are
- Chemical processing plants and equipment
- Food and dairy processing plants
- Utility plants
- Plant maintenance coating
- Pipe coating
- Tank coating
||50 minutes @ 75°F
||2Part"A"to1Part"B" By Volume
||12 hours @ 72°F
||7 days@ 72°F
||4 hours @ 220°F
|Recommended Film Thickness
||2 Coats @ 10-15 mils each
CURED CHEMICAL RESISTANCE:
Acids, alkalies, alcohols, ketones, aromatics and other solvents.
Remove dirt, loose particles and oil contaminants by scarification,
sandblasting, etc See
Epoxy.com Surface Preparation Guide for more
Mix 2 parts "A" Component with 1 part "B" Component using a low-speed,
1/2" Epoxy.com - Mixing Paddle for 3-5 minutes. Apply immediately. High
temperatures will shorten pot life.
Epoxy.com Product #647 can be applied by brush, roller, pour or spray.
Epoxy.com Product #647 can be easily made into a heat resistant epoxy
grout by adding from 1 to 3 parts by volume of Epoxy.com Product #76 Epoxy
Extender to the mixed epoxy.
Epoxy.com Product #647 is designed
to be applied in two (2) coats at approximately 150 SF/gallon per coat.
3 gallons Epoxy.com Product #647 + (3) 48 lb. bags
Epoxy.com Product #76 = 2,246 cu. in. per unit
“A” Component contains epoxy resin. DANGER! “B” Component contains
alkaline amines; strong sensitizer. May cause skin sensitization or other
allergic responses. Use with good ventilation, particularly if material is
heated or sprayed. Prevent all contact with skin or eyes. Wear protective
clothing, goggles, gloves and/or barrier creams. Keep container closed when
not in use. Wash thoroughly after handling.
FIRST AID: In case of skin contact, immediately
wash with soap and water. In case of eye contact, flush eyes with copious
amounts of water for at least fifteen (15) minutes. Remove contaminated
clothing shoes. If irritation persists, seek medical attention. Wash
clothing before reuse.
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]