Epoxy.com Product #447
Waterproofing Elastomeric Membrane
DESCRIPTION:
Epoxy.com Product #447 Waterproofing Membrane is a latex-based
liquid membrane.
Epoxy.com Product #447 offers a non-toxic, one part flexible solution
for a wide range of waterproofing and vapor-proofing applications.
ADVANTAGES:
- Flexible and elastic membrane
- Water-based compound that can be applied to damp surfaces
- Tough abrasion-resistant coating
- Low water vapor permeability
- Non-staining
- Ultraviolet resistant
- Bonds well to many surfaces
- Can be applied by brush, roller or spray
- Quick drying; typically dry to the touch in one hour
- Low odor
- Alkali-resistant, can be applied to alkaline surfaces
WHERE TO USE:
The liquid membrane can be used in a wide variety of applications where
high flexibility and good bonding are required.
- Floors—typical applications include use beneath self-leveling floor
products or above trowelable underlayments where the original membranes
have been punctured.
- Basements—The liquid membrane can be used as part of a waterproofing
system below ground level.
- Walls—The liquid membrane has good adhesion to many types of
surfaces.
PHYSICAL PROPERTIES:
|
pH
|
9.0
|
|
Weight Per Gallon
|
9.2
|
|
Viscosity
|
20,000cps
|
|
Finish
|
Semi-gloss
|
|
Tensile Elongation ASTM D-638
|
|
21 day dry
|
562
|
| 7 day dry/21 day wet |
657 |
| Permeability ASTM E-96 |
0.013 |
| Tensile Strength ASTM D-638 |
| 21 day dry |
345 |
| 7 day dry/21 day wet |
562 |
| Water Vapor Transmission ASTM E-96 |
0.085 |
| Low Temp Flex & Crack Bridging ASTM C 836 sec. 5.7 |
0°F No cracks No cracks |
| Hydrostatic Resistance ASTM D-751 Procedure B |
Passes |
| ANSI 118.10 |
Specification |
| Fungus & Micro Organism Resistance |
Epoxy.com Product #447 does not support mold growth |
|
Damp-Proofness
|
No visible water penetration after 48 hours |
APPEARANCE:
The liquid vapor membrane is waterbased latex that dries to form a tough,
water and vapor-resistant film. The latex is environmentally friendly and
solvent free. The liquid membrane has low odor. Epoxy.com Product #447
is available in a variety of colors. The color of the liquid compound may
differ slightly from the color of the dried membrane. The formulated product
is a viscous liquid similar in consistency to a thick water-based paint.
SURFACE PREPARATION:
Newly prepared surfaces should be smooth and have a troweled or brushed
finish. All masonry should be flush pointed. Defects in existing surfaces
should be repaired. The surface needs to be clean and free of dust, loose
material, and free surface water. The membrane should not be applied under
wet conditions or where these conditions are likely to occur before the
membrane has fully dried. It is sometimes advantageous to pre-wet the
substrate so it is damp, yet free of standing water, to improve adhesion of
the liquid membrane. Check adhesion to various surfaces by applying the
product to a small sample area before starting any job.
APPLICATION:
The liquid may be applied by brush, roller or airless spray. If
necessary, the compound can be diluted with water. However, care should be
taken to ensure the correct dry-coat thickness is applied and that the
drying time is not unacceptably extended due to the dilution.
The thickness of the dried membrane depends on the application
requirements and method of application. For a single dry coat thickness of
more than 0.3 mm, it is recommended that the membrane be applied by airless
spray. If airless spray is used, single dry-coat thickness of up to 1 mm can
be obtained.
If two coats are being applied, it is recommended that the coats be
applied at right angles to each other. Before applying the second coat, it
is necessary to let the first coat become dry to the touch. It is preferable
that the second coat is applied within 24 hours after the application of the
first.
COVERAGE:
Two coats are required. Epoxy.com Product #447 should be applied
at a rate of 80 square feet per gallon.
PACKAGING:
1 gallon, 5 gallon and 55 gallon drums
SHELF LIFE:
One (1) year
LIMITATIONS:
Protect from freezing. Do not apply below 40°F.
CAUTION:
Avoid ingestion of material. Wash thoroughly after handling.
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers. |
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Home]
[Catalog of Products]
[Where to Start]
[[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive Flooring]
[Applications]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Industrial Floors]
[Injection]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Novolac Epoxy]
[Polymer Systems]
[Primers Sealers]
[Misc.]
[Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]
6516991
|