Epoxy.com Product #256
Impact and Chemical Resistant Coating
DESCRIPTION:
Epoxy.com Product #256 Impact and Chemical Resistant
Coating is a 100%
solids epoxy coating specifically formulated and manufactured to
produce a
tough, impact resistant coating. Epoxy.com Product #256
is a chemically modified epoxy
and has high tensile strength and tensile elongation. These
properties prevent
cracking from impact or expansion/contraction cycles caused by
temperature
changes. Epoxy.com Product #256 will resist
chipping from impact.
ADVANTAGES:
- Epoxy.com Product #256 is a solvent free,
water insensitive epoxy that can be applied to
moist or dry surfaces.
- Epoxy.com Product #256 is ideal for the
encapsulation of lead paint.
- Epoxy.com Product #256 is excellent for
secondary containment, on concrete, concrete
blocks or other construction materials.
- Epoxy.com Product #256 can be rolled,
brushed or squeegeed.
- Epoxy.com Product #256 maintains excellent
flexibility to -20° F and is not affected by
expansion/contraction cycles caused by changing temperatures.
- Epoxy.com Product #256 is resistant to
hydrogen sulfide, methane and other harsh
exposures found in soil and tunnel construction.
- Epoxy.com Product #256 is used on floors,
ramps, garage decks as a non-skid or non-slip
surface with an aggregate broadcast, using Epoxy.com
Product #75 or Product #81 Aggregate.
- Epoxy.com Product #256 has extremely low
vapor transmission rates when tested in
accordance with ASTM D-1434.
- The tensile elongation properties are locked into the epoxy
molecular structure
and will not change with aging.
PHYSICAL PROPERTIES
|
Color
|
Fed #595A Gray 26622 (Other colors available as
special order products)
|
|
Viscosity @ 72°F (22.2° C)
|
10,000 cps
|
Pot Life
100 grams @ 72°F (22.2° C)
|
25 min
|
|
Shore Hardness
D Scale
|
70
|
Tensile Elongation
ASTM D-638
|
40%
|
|
Tack Free Time
@ 72°F (22.2°C)
|
8 Hours
|
|
Final Cure
|
7 Days
|
Epoxy.com Product #256 Impact and Chemical Resistant
Coating or Mortar can
be used as a mortar with the addition of 3 to 4 parts
Epoxy.com Product # 76 Epoxy Extender.
This will produce a mortar with a lower modulus of elongation
that will not fail
(pull away from the weaker concrete) in changing temperature
cycles.
SURFACE PREPARATION
For best results, areas to receive the Epoxy.com Product
#256 Impact and
Chemical Resistant Coating or Mortar must be free of
dirt, grease and
laitance. Abrasive blasting, water blasting, wire brushing or
shot blasting is
recommended for surface preparation. Steel should be cleaned to
SSPC-SP6.
MIXING
Stir "A" Component before mixing "A" & "B" Components together.
Mix one part "A"
Component to one part B component by volume for three minutes
with slow speed
drill and Epoxy.com Mixing Paddle. Avoid
entrapping air.
COVERAGE
Epoxy.com Product #256 will cover 100 sq.
ft/gal. applied to a smooth surface at 15 mils
thick. Two (2) coats are recommended. Coverage will decrease
when applied to a
rough surface.
PACKAGING
Epoxy.com Product #256 Impact and Chemical Resistant
Coating or Mortar is
packaged in two (2) gallon and ten (10) gallon units.
CAUTION:
WARNING! "A" Component contains epoxy resin. DANGER! "B"
Component contains
alkaline amines; strong sensitizer. May cause skin sensitization
or other
allergic responses. Use with good ventilation, particularly if
it is heated or
sprayed. Prevent all contact with skin and eyes. Wear protective
clothing,
goggles, gloves and/or barrier creams. Keep container closed
when not in use.
Wash thoroughly after handling.
FIRST AID:
In case of skin contact, immediately wash with soap and water.
In case of eye
contact, flush with copious amounts of water for at least 15
minutes. Remove
contaminated clothing and shoes. If irritation persists, seek
medical attention.
Wash clothing before reuse.
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
Untitled Page
Proper mixing and installation is critical to the optimal success of all
product. See Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
375 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2007 EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy
Systems™ Product Company ("ESI") warrants its products (when properly stored)
for the period of time as follows: Epoxies, Product #315, Product #315BC, and
Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2)
months and Polyurethanes Four (4) months; Power Tools and Equipment 90
days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all
other resins (not specifically mentioned above) 30 days; hand tools (non-power
tools) 30 days. ESI warrants that its products will be free of
manufacturing defects and will be in conformity with published specifications
when handled, stored, mixed and applied in accordance with recommendations of
ESI. If any product fails to meet this warranty, the liability of ESI will be
limited to replacement of any non-conforming material if notice of such
non-conformity is given to ESI within the warranty period for the material (as
indicated above), or within 1 year of the delivery of materials (whichever is
sooner). ESI may in its discretion refund the price received by ESI in lieu of
replacing the material. No customer, distributor, or representative of ESI is
authorized to change or modify the published specifications of this warranty in
any way. No one is authorized to make oral warranties on behalf of ESI. In order
to obtain replacement or refund the customer must provide written notice
containing full details of the non-conformity. ESI reserves the right to inspect
the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED
WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY
UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY,
WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of
our products are made on an individual order basis. Unless
authorized in writing by Epoxy Systems, Inc. in writing before the material is
made, there are no returns on items purchased from us, once the order has been
processed, and the material made. In the event of authorized returns a
restocking charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on non-list
priced items. All Returns are for merchandise (store) credit only, no cash
or credit card credits. In the event of a return, buyer is responsible for
the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
Secure Login