Epoxy.com Standard Epoxy Mortar uses 100% solids Epoxy with graded aggregates. Urethane and Epoxy finish coats provide specific performance characteristics as needed
Epoxy.com Standard Epoxy Mortar is a resin patching, flooring, and/or repair system consisting of 100% solids epoxy resin and aggregates which provide heavy-duty protection at 3/16" to 1/4". When grouted an sealed, Epoxy.com Standard Epoxy Mortar eliminates porosity and produces a dense, skid-inhibiting finish that will minimize dirt and chemical penetration.
Epoxy.com Standard Epoxy Mortar can also be installed with a conductive system for dispassion of static electricity in areas that are subjected to physical abuse and moderate to heavy wear and impact.
Epoxy.com Standard Epoxy Mortar is trowel applied and can be used to form an integral cove base where specified. It has good chemical resistance and is designed for high impact and heavy duty use.
Epoxy.com Standard Epoxy Mortar (HP) is the High Performance Mortar exhibiting excellent chemical resistance and utilizes Epoxy.com Product #2 Chemical resistant Resin or Epoxy.com Product #630 Novolac Epoxy for maximum resistance.
Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, shot blasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast immediately prior to application.
Roll or squeegee a prime coat. Trowel apply mortar to desired thickness. Grout and Top Coat as needed to achieve required finish and texture.
Do not use in temperatures below 55 degrees F, as cooler temperatures delay hardening. Substrate must be free from hydrostatic pressure, moisture transmission, curing agents and other foreign materials. Urethane seal coats are recommended for areas exposed to intense sunlight. Allow 16 hours for initial set of mortar. Seal Coat time may vary.
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent
APPLICATION PROPERTIES @77° F
|Mix Ratio||4:1 by volume|
|Color||Clear, Standard Colors,
Color matching also available
|Initial Cure||16 hours|
PHYSICAL AND PERFORMANCE PROPERTIES
|Compressive Strength (ASTM D-695||13000 PSI (neat resin)|
|Ultimate Tensile Strength (ASTM D638)||4200 PSI (neat resin)|
|Tensile Elongation (ASTM D-638)||6-8% (neat resin)|
|Flexural Strength (ASTM D-790)||7800 PSI (neat resin)|
|Flexural Modulus (ASTM D-790)||2.5 x 105 PSI|
|Tensile Strength (ASTM C-307)||2400 PSI|
|Weight at 1/4 inch thick||2.0 - 2.5 #/sq. ft.|
|Adhesive Strength (Mil D-24613)||420 PSI|
|Adhesion to Concrete (ACI Committee 403)||300 PSI (Concrete Fails)|
|Hardness Shore D (ASTM D-2240)||80-84|
|Water Absorption (MIL D-24613)||Nil|
|Abrasion Resistance (ASTM C-501)||50 mg|
|Impact Resistance (MIL-D-3134F SS 4.7.4||Withstands 16 ft/lbs without cracking, delaminating, or chipping.|
|Compressive Strength (ASTM C-579)||14000 PSI @ 7 days|
|Flexural Strength (ASTM C-580)||4,200 PSI|
|Coefficient of Friction (ASTM D-2047)||0.80|
Coefficient of Expansion
|26 x 10-6 in/in/degree F.|
|Thermal Shock Resistance (ASTM C-884)||Passed|
(Mil -F-52505 SS18.104.22.168
support growth of fungus or bacteria
when subjected to mildew and bacteria tests specified in TT-P-34