Epoxy.com Product #301

Cold Cure Epoxy Injection Resin

Low-Mod Low Viscosity

Zero (0) VOC Epoxy - meets most stringent low VOC standards

Low Temperature Self Leveling Epoxy Injection Resin

GENERAL DESCRIPTION

Epoxy.com Product #301 Cold Cure Epoxy Injection Resin Resin is a 100% solids low-mod, low viscosity, low temperature curing Primer and Sealer. Epoxy.com Product #301 Cold Cure Epoxy Injection Resin Resin is 100% solids with "0" (zero) VOC, which means it has virtually no order and will meet even the strictest low VOC standards.

Epoxy.com Product #301 Cold Cure Epoxy Injection Resin Resin is specially formulated for cold temperature applications. Epoxy.com Product #301 Cold Cure Epoxy Injection Resin Resin is able to cure down to 35°F. Epoxy.com Product #301 Cold Cure Epoxy Injection Resin Resin is often used in outdoors, in food preparation areas that need to be kept at a constant temperature.

ADVANTAGES

Moisture insensitive (cures on damp or wet surfaces)
Withstands movement from thermal change
Low Temperature Cure - Super Fast Cure at Room Temperature
Meets ASTM C-881 Type III, Grade 1 Class B and C std. spec.
100% Solids "0" (zero) VOC - meets the strictest low VOC standards
Low Viscosity - Excellent wetting properties
Good shock absorption qualities
Versatile
Forms Virtual Moisture Barrier

SURFACE PREPARATION

Surface must be clean and sound. Interfaces of cracks must he free of dirt, laitance, grease, curing compounds and other foreign matter. Flushing with water through ports under pressure may he necessary prior to epoxy injection. Cracks may be damp or wet.

MIXING INSTRUCTIONS

Temperature of Epoxy.com Product #301 Cold Cure Epoxy Injection Resin must he 40? F. or above at time of mixing. Stir each component separately before blending. Best if used in an automatic binary mixing system. If mixed manually mix two parts by volume of Part A with one part by volume of B for three minutes with a low speed electric drill motor equipped with a mixing paddle.

APPLICATION

For pressure injection set ports at intervals that approximately equal the thickness of the member to be injected in inches. Ports may need to place closer together for very fine cracks, or may be slightly further for wider cracks. Seal between and around each port with Epoxy.com Product #5, or #6. Inject Product #301 from an epoxy injection machine or binary hand or pneumatic injection gun. For more information consult Epoxy.com technical service department.

LIMITATIONS

Use of solvents for thinning will prevent proper cure of Epoxy.com Product #301 Cold Cure Epoxy Injection Resin Resin . New concrete must be 28 days old prior to application of Epoxy.com Product #301 Cold Cure Epoxy Injection Resin Resin. Temperature of substrate must be above 34° F. Works best if the substrate is above 40° F.

SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

CLEANUP

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.

APPLICATION PROPERTIES @77°F

Mix Ratio	2:1 By Volume
Viscosity	600-750cps
Pot Life (200 gr.)	15 minutes @ 75° F.
Tack Free to Touch	2-3 hours @ 75°F; 14-16 hours @ 35° F.
Recoat	3-4 hours @ 75° F; 14-16 hours @ 35° F.
Light Traffic	5-6 hours @ 75° F; 24 hours @ 35° F.
Final Cure	5 Days
Packaging (unit size)	3 gal., 15 gal.
Standard Colors	clear
Colors	Standard Colors Available at an Additional Charge

PHYSICAL PROPERTIES

Elongation (ASTM D-638)	Greater than 10%
Compressive Strength (ASTM D-695)	10,000 PSI (min)
Tensile Strength (ASTM D-790)	3,500 PSI
Concrete Bond Strength (ASTM C-882)	2,290 PSI
Shrinkage (ASTM C-883)	Passed Test
Thermal Compatibility (ASTM C-884)	Passed Test
Adhesion to Concrete (ACI Committee 403)	250 PSI (concrete fails)