Epoxy Polyurethane Polyester MMA - Methyl Methacrylate, other Resin Systems Over 350 Products Since 1980

Epoxy.com Product #315BC

100% Solids High-Build Polymeric Coating


Epoxy.com Product #315BC High-Build Polymeric Coating is a two component, 100% solids polymeric Hi-Build polymeric coating used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, pools etc. Also used as a base coat for Epoxy.com Chip Flooring System .


Epoxy.com Coating on a Water Tank
  • Moisture Insensitive
  • Ceramic like finish
  • Sprayable
  • Solvent Free
  • Waterproof
  • Extremely Durable
  • Chemical Resistant


Surface  to receive Epoxy.com Product #315BC High-Build Polymeric Coating must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast immediately prior to application.


Temperature of Epoxy.com Product #315BC High-Build Polymeric Coating (normal cure) must be 50° F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part  B for three minutes with a low speed electric drill motor equipped with a mixing paddle. 


ApplyEpoxy.com Product #315BC High-Build Polymeric Coating with a roller, brush, or spray equipment.  When not used as part of the 315 Chip Flooring System, 2 coats are recommended. Thickness per coat should be 7-10 mils. Seven days cure time is required to reach maximum chemical resistance. When installing over concrete Product #899 or Product #203 Primer is recommended.


DO NOT apply Epoxy.com Product #315BC High-Build Polymeric Coating at temperatures below 50° F. Surface must be dry.


Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.


All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent


Mix Ratio  2:1 By Volume 
Viscosity (mixed) 950 CPS       
Pot Life (200 gr.) in minutes @70° F. 30-40(normal cure)
Set Time in Hours @ 70° F. 10-12 (normal cure)
Initial Cure 24 Hours
Final Cure 5 Days
Packaging Unit Size 3 gallon units (2 gallons of "A" + 1 gallon of "B"
Standard Colors White, Light Gray, Dark Gray, Taupe, Sand,
Old Gold, Mocha, Brick Red, Slate Blue,
Colonial Green, Deep Blue, Black, Safety Yellow
Color Chart HereClick the picture of color card below  for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

Material Certification of LEED Requirements

Epoxy.com a division of Epoxy Systems, Inc. certifies that Epoxy.com  meet or exceed LEED requirements as summarized below:

LEED Credit IE 4.2:

Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 4.2 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.

Other customers who visited this page also visited:

For more information please contact:

A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems ,
Since 1980 - Over 33 years
Florida & Vermont

Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time) .
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright © 1994-2019 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.