|
||
| [Contact Us] | ||
Epoxy Chip Floor Base Coating
Epoxy.com Chip Flooring System
GENERAL DESCRIPTION
Epoxy.com Product #315BC High-Build Polymeric Coating is a two component, 100% solids polymeric Hi-Build polymeric coating used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, pools etc. Also used as a base coat for Epoxy.com Chip Flooring System.
ADVANTAGES
- Moisture Insensitive
- Ceramic like finish
- Sprayable (with the right equipment)
- Solvent Free
- Waterproof
- Extremely Durable
- Chemical Resistant
SURFACE PREPARATION
Surface to receive Epoxy.com Product #315BC High-Build Polymeric Coating must be clean and sound. Remove all dirt, laitance, grease curing compoundsand other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blastimmediately prior to application.
MIXING INSTRUCTIONS
Temperature of Epoxy.com Product #315BC High-Build Polymeric Coating (normal cure) must be 50° F or above at time of mixing. Stir eachcomponent separately before blending. Mix two parts by volume of Part A withone part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.
APPLICATION
Apply Epoxy.com Product #315BC High-Build Polymeric Coating with a roller, brush, or spray equipment. When not used as part of the 315 Chip Flooring System, 2 coats are recommended. Thickness per coat should be 7-10mils. Seven days cure time is required to reach maximum chemical resistance.When installing over concrete Product #12 or Product #899 Primer isvrecommended.
LIMITATIONS
DO NOT apply Epoxy.com Product #315BC High-Build Polymeric Coating at temperatures below 50° F. Surface must be dry.
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, washimmediately and seek medical help. Use safety glasses with side shields andwear protective rubber gloves.
CLEANING
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
APPLICATION PROPERTIES @77°F |
|
| Mix Ratio | 2:1 By Volume |
| Viscosity (mixed) | 950 CPS |
| Pot Life (200 gr.) in minutes @70° F. | 30-40(normal cure) |
| Set Time in Hours @ 70° F. | 10-12 (normal cure) |
| Initial Cure | 24 Hours |
| Final Cure | 5 Days |
| Packaging Unit Size | 3 gallon units (2 gallons of "A" + 1 gallon of "B" |
| Standard Colors |
White, Light Gray, Dark Gray, Taupe, Sand, Old Gold, Mocha, Brick Red, Slate Blue, Colonial Green, Deep Blue, Black, Safety Yellow |
Click the picture
of color card at the side for a larger version of this picture of the
color chart.
Please note:
The picture to the right is a photographic reproduction
of the color card for this product. The photo reproduction process and
your monitor and/or printer will change these colors. This chart is to
give you an idea of the colors available and not intended for critical
color selections.
Material Certification of LEED Requirements
Epoxy.com a division of Epoxy Systems, Inc. certifies that Epoxy.com meet or exceed LEED requirements as summarized below:
LEED Credit IE 4.2:
Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 4.2 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Other customers who visited this page also visited:
- Epoxy.com Product #1 - All Purpose Epoxy Coatig
- Epoxy.com Product #1W - Wall Grade Version of Epoxy.com Product #1
- Epoxy.com Product #2 - Chemical Resistant Epoxy coating.
- Epoxy.com Product #633 - Epoxy Novolac Coating - extremely chemical resistant
- Epoxy.com Chip Flooring System
- Epoxy.com Coatings Page.
Proper mixing and installation are critical to the success of all products. See Installation Tips, Techdata, and (M)SDS for more details, or contact us with any questions.
321-206-1833 Customer Service – Ordering and Order Status
Katey Lambert-Fontaine – Vice President & Chief Operations Officer
[email protected]
352-533-2167 Technical Support
Norm Lambert – President & Technical Support Director
[email protected]
Debby Lambert, Co-Founder and Strategic Planning
Website: www.epoxy.com
24-hour Hazmat Emergency Telephone Response Service: 1-800-633-8253
[Home] [Catalog of Products] [SDS] [Online Ordering Authorization Form]