[Epoxy Home] [Catalog of Products] [Where to Start] [Guide Specs] [Epoxy Installation Guides] [Blog Posts] [Epoxy Bonding Systems] [Chip Floors] [Chemical Resistant Epoxy] [Seamless Coatings] [Conductive Epoxy Flooring] [Crack Injection of Concrete & Wood] [Applications] [Elastomeric Polyurethane Systems]  [Seamless Garage Flooring Resins] [High Temperature Epoxy Resins] [Seamless Industrial Floors] [Joint Systems & Sealants] [Methyl Methacrylate MMA ] [Novolac Epoxy Resins] [Epoxy Mortars & Grouts] [Epoxy Novolac] [Primers Sealers] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Epoxy Installation Tips] [Who We Are]  [Epoxy Tech Data Sheets in Acrobat] [Product MSDS Sheets] [Online Order Authorization Form][Contact UsPhone 352.489.1666

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980Contact Us  

Epoxy.com Product #2

Guide Specification

Water Tank Installation


PART 1 GENERAL

1.1 SECTION INCLUDES

A. Products.
B. Transportation and handling.
C. Storage and protection.
D. Product options.
E. Substitutions.

1.2 RELATED SECTIONS  

1.3 PRODUCTS

A. Do not use materials and equipment removed from existing premises, except as specifically permitted by the Contract Documents.

B. Instructions to Bidders: Product options and substitution procedures – No Product substitutions will be permitted.

1.4 TRANSPORTATION AND HANDLING

A. Transport and handle Products in accordance with manufacturer's instructions.

B. Promptly inspect shipments to ensure that Products comply with requirements, quantities are correct, and Products are undamaged.

C. Provide equipment and personnel to handle Products by methods to prevent spillage, contamination, or damage.

1.5 STORAGE AND PROTECTION

A. Store and protect Products in accordance with manufacturers' instructions, with seals and labels intact and legible.

1.6 PRODUCT OPTIONS

A. Product Specified by Naming Manufacturer: Epoxy.com Product #2 as supplied by Epoxy.com. Only products of manufacturers named and meeting specifications will be allowed in the tank, no options or substitutions allowed.

1.7 SUBSTITUTIONS

A. No Product substitutions will be allowed.

PART 2 PRODUCTS

Product used shall be Epoxy.com Product #2 from Epoxy.com a division of Epoxy Systems, Inc. of Florida and Vermont - 352-489-1666

PART 3 EXECUTION

Not Used

END OF SECTION

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Surface preparation and field application of paints and coatings.

1.2 RELATED SECTIONS

1.3 DEFINITIONS

A. Conform to ASTM D16 for interpretation of terms used in this Section.

1.4 SUBMITTALS

A. Submit under provisions of Section 01041.

B. Product Data: Provide data on all finishing products and special coatings.

C. Manufacturer's Instructions: Indicate special surface preparation procedures and substrate conditions requiring special attention.

1.5 QUALIFICATIONS

A. Manufacturer: Company specializing in manufacturing the Products specified in this section with minimum 10 years experience.

1.6 REGULATORY REQUIREMENTS

A. All work shall conform to all pertinent laws, ordinances and regulations of all bodies having jurisdiction. Comply with applicable codes, rules, regulations and building and safety laws relating to construction, public health and safety.

B. Contract Documents take precedence when they are more stringent than codes, ordinances, standards and statutes. Codes, ordinances, standards and statutes take precedence when they are more stringent or conflict with drawings and specifications. The following industry standards, specifications and codes are minimum requirements, (latest issue as adopted by local jurisdiction as of date of Contract):

1. Applicable Federal, State, County and Municipal laws and ordinances.

2. National Electrical Manufacturer's Association Standards

3. National Electrical Code

4. Underwriter's Laboratories, Inc. Standards

5. American National Standards Institute

6. American Society for Testing Materials Standards

7. National Fire Protection Association Standards

8. Occupational Safety and Health Act – OWNER intends to strictly enforce all OSHA requirements pertaining to working in confined area.

9. All State and Local Occupational Safety and Health Act(s), laws, or regulations.

10. OWNER Contractor Safety Guidelines – OWNER requires every member of the work crew and all sub-contractors read this manual and sign a statement attesting to the fact they have read, understand and concur with the guidelines.

11. OWNER Safety Department Guidelines

12. BOCA Code

13. American Gas Association

1.7 FIELD SAMPLES

 

1.8 DELIVERY, STORAGE, AND HANDLING

A. Deliver, store, protect and handle products to site under provisions of Section 01600.

B. Deliver products to site in sealed and labeled containers; inspect to verify acceptability.

C. Container label to include manufacturer's name, type of Coating, brand name, lot number, and instructions for mixing and reducing.

D. Store paint materials at minimum ambient temperature of 50 degrees F and a maximum of 90 degrees F degrees ), in ventilated area, and as required by manufacturer's instructions.

1.09

Not used

1.10 ENVIRONMENTAL REQUIREMENTS

A. Do not apply materials when surface and ambient temperatures are outside the temperature ranges required by the paint product manufacturer.

B. Do not apply coatings when surface is wet, or damp. Dry substrate before application of coating.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Epoxy.com Product No.2. as supplied by Epoxy.com a division of Epoxy Systems, Inc. of FL and VT. Apply to final coating thickness of 14 mil (minimum).

B. Primer Coat: Self priming.

C. Substitutions: Under provisions of Section 01600 – NO SUBSTITUTIONS SHALL BE PERMITTED. No other coating or coating material may be used inside the tank.

2.2 MATERIALS

A. Coatings: Epoxy.com Product #2

B. Accessory Materials:

1. DO NOT Thin the coating, unless specifically directed to do so by the Material Manufacturer in writing. If directed by the manufacturer, thinning must be done exactly to his/her specifications, and direct supervision by a factory representative.
2. Use solvents only for cleanup of tools and equipment. All solvents must be approved in advance by OWNER and the Material Supplier/System Consultant. Care will be taken to insure that no material is spilled onto the ground or leaked into the environment in any way. Waste solvents will be disposed of in accordance with Federal, State, Local, and OWNER regulations.

2.3 FINISHES

Not Applicable

PART 3 EXECUTION

3.1 EXAMINATION

A. Verify site conditions are satisfactory for proper application of coating materials.

B. Verify that substrate conditions are ready to receive work as instructed by the product manufacturer.

C. Examine surfaces scheduled to be finished prior to commencement of work. Report any condition that may potentially affect proper application to OWNER Project Coordinator and Material Supplier/System Consultant.

3.2 PREPARATION

A. Report defects and unclean surfaces which affect work of this section, to the Engineer.

B. Steel and Iron Surfaces: Remove existing coating by sandblasting down to bare white metal.

C. Concrete surfaces - Abrasive clean as required to insure proper bonding.

3.3 APPLICATION

A. Apply products in accordance with manufacturer's instructions.

B. Protect all surfaces that are not to be coated (pipe opening, drains etc.)

C. Apply primer coat or first coat as soon after surface prep as physically possible. This first application must be done to steel surfaces before flash rusting can occur. If flash rusting occurs, do not continue with coating until all flash rust has been removed.

D. Do not apply finishes to surfaces that are not dry.

E. Apply each coat to uniform finish.

F. Allow applied coat to dry before next coat is applied.

G. Re-coat within 24 hours of the previous coating. If more than 24 hours passes between coats the Manufacturer and/or OWNER may direct the Contractor to roughen the last coat to insure proper bonding. If this happens the cost of this roughening and the cost of additional coating, plus all labor associated with this work will be considered to be the sole responsibility of the Contractor.

H. Ensure all wetted surfaces of hatch covers, sealing surface and openings are properly coated.

3.4 FINISHING MECHANICAL AND ELECTRICAL EQUIPMENT

Not Applicable.

3.5 FIELD QUALITY CONTROL

A. An indepentent engineer or certified inspection firm’s representative shall test the coating

B. Testing Shall include:

1. Wet Film Thickness Testing – Coating contractor may perform this test himself.
2. Dry Film Thickness Testing
3. Testing for holidays by spark testing

3.6 CLEANING

A. Collect waste material which may constitute a fire hazard, place in closed metal containers with appropriate labeling. Place in area designated by OWNER Project Coordinator for removal by OWNER.

3.7 SAFETY PRECAUTIONS

A. Ventilation: Provide adequate tank ventilation per Manufacturer's recommendations.

B. Equipment used in tank shall be non-sparking, grounded, and/or explosion proof.

C. All electrical cords shall be equipped with GFI safety devices per OWNER Safety Guidelines.

D. A "Watch" person shall be located at the manhole open e.g. on the exterior of the tank at any time the tank has a workman inside.

E. Use air-supplied masks and skin protective clothing during blasting and coating operations.

F. Air for certified air-supplied masks shall be supplied by a source other than the compressor used for blasting and/or painting.

G. Ensure entry into the tank is prohibited until approved by OWNER .

H. All work in confined space (inside tanks) shall be performed in strict accord with applicable OSHA regulations. Contractor shall provide OWNER with copies of all certifications required by OSHA regulations at time of bid.

I. Contractor is responsible to provide, maintain and operate all environmental monitoring devices required to measure oxygen levels, contaminant levels, etc. per OSHA requirements.

END OF SECTION

Hit Counter

retro jordans for sale kate spade outlet sport blue 3s Louis Vuitton Outlet jordan 3 wolf grey legend blue 11s louis vuitton outlet cheap jordans lebron 12 louis vuitton outlet coach outlet online retro jordans for sale louis vuitton outlet louis vuitton uk wolf grey 3s lebron 12 sport blue 3s coach factory outlet cheap jordan shoes wolf grey 3s

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter