 |
Product #1 All Purpose Coating
- a 100% solids epoxy Hi-Build epoxy coating used for high foot and
light forklift traffic areas where abrasion resistance is required;
for protection against mild corrosion; and as a decorative
waterproof coating for walls, floors, tanks, etc Available in
normal, fast, and Cold Temperature Cure versions.
|
|
|
Product #1Fast - Shorter
Potlife, and faster setting version of
Product #1 , |
|
|
Product #1Cold Temperature
Cure
- This is a version of Product #1
that sets even faster than Product#1 Fast. Typically used in colder
temperatures, or where an very fast cure is required. |
|
|
Product #1W a two
component, 100% solids epoxy Hi-Build epoxy coating used for high indoor
traffic areas where abrasion resistance is required; for protection
against mild corrosion; and as a decorative waterproof coating for
walls, tanks, etc. |
|
|
Product #2 Chemical Resistant
Coating - a two component, 100% solids epoxy chemical
resistant coating used to protect chemical concrete, steel and other
structural materials from non-oxidizing acids and alkalines for both
interior and exterior applications. Available in normal, fast, and Cold
Temperature Cure. |
|
|
Product #2 Fast - Shorter
Potlife, and faster setting version of
Product #2 |
|
|
Product #2 Cold Temperature Cure
- This is a version of that sets even faster than Product#2 Fast.
Typically used in colder temperatures, or where an very fast cure is
required. |
|
|
Product #2W a two
component, 100% solids epoxy chemical resistant coating used to protect
chemical concrete, steel and other structural materials from
non-oxidizing acids and alkalines for both interior and exterior
applications. |
|
|
Product #3 Injection Resin 3.5:1-
a proprietary low viscosity, high modulus, quick strength, epoxy-based
binder developed for structurally rebonding cracks, delaminations and
hollow planes in Portland cement concrete. Can also be used in certain
types of wood injection. If you are looking for a 2:1 mix ration please
see Epoxy.com
Product #300-306 |
|
|
Product #4 Urethane Injection
- a one-component, "Acetone Free", MDI based hydrophilic sealing and
grouting compound used to stop water leaks in wet environments. Product
#4, as it mixes with existing water, cures rapidly into a tough,
flexible, closed-cell compound which is insoluble to water and most
other chemicals. |
|
|
Product #5 Fast Set Gel Adhesive
- a 100% solids high-mod epoxy gel adhesive used for vertical and
overhead bonding applications and structural repairs. It is also used as
a grout for anchor bolts, dowels and rebar. |
|
|
Product#6 Gel - Normal Setting
Adhesive - high-mod epoxy gel adhesive used for vertical and
overhead bonding applications and structural repairs. It is also used as
a grout for anchor bolts, dowels and rebar.
|
|
|
Product #6SC Long Pot life Adhesive
produces a non-sagging material that is ideal for repairs
on vertical or overhead surfaces. PRODUCT #6SC meets or exceeds the
requirements of ASTM - C881-87, Types I, II, and IV, Grade 3 Class "B"
and "C"
|
|
|
Product #7 All Purpose Epoxy
Bonding Agent is a two component, 100% solids epoxy resin
system designed to bond new concrete to old and other
materials to concrete. It has a convenient 1:1 mix ratio, by volume with
a viscosity similar to heavyweight oil. It exceeds the requirements of
ASTM C-881-90, Types I, II, IV and V, Grade 2, Class "B" and "C". |
|
|
Product #7SC - a 100%
solids high-mod epoxy adhesive used to bond fresh concrete to cured
concrete, steel to fresh or hardened concrete, as a grout for anchor
bolts, dowels and rebar, as a binder for epoxy concrete, and for bonding
other dissimilar materials. It is similar to Epoxy Systems’ ™ Product #7
but with a slower cure to allow more time for concrete pours. |
|
|
Product #8: Replaced by
Product 870 Penetrating Epoxy Sealer) |
|
|
Product #9- Lo Mod Mortar Adhesive -
uses 100% solids Epoxy with graded aggregates. Urethane and Epoxy
finish coats provide specific performance characteristics as needed. It
is a resin patching, flooring, and/or repair system consisting of 100%
solids epoxy resin and aggregates which provide heavy-duty protection at
3/16" to 1/4". When grouted an sealed, EpoxySystems' Epoxy Mortar STD
eliminates porosity and produces a dense, skid-inhibiting finish that
will minimize dirt and chemical penetration. |
|
|
Product #10
Lo-Mod Adhesive- a 100% solids Lo-Mod Low Viscosity
adhesive used as a binder for epoxy mortar systems in patching and
grouting applications, as a seal coat for non-skid surfaces outside, and
as a primer to insure high bond strength for coatings and patches. |
|
|
Product #10FAST
Lo-Mod Adhesive -Fast Cure |
|
|
Product #10COLD
Lo-Mod Adhesive Cold Temperature Cure |
|
|
Product #11 Epoxy Joint Filler
- a 100% solids flexible epoxy joint filler for saw-cut joints of
concrete slabs on grade, or to repair existing slabs. Product #11
absorbs the impact and shock of heavy loads and steel wheeled traffic,
preventing erosion of control joint edges. |
|
|
Product #12 Epoxy Primer
- a two component, seamless 100% solids epoxy primer system with High
Chemical Resistance and High Bond Strength. The epoxy may be applied as
a primer for most High End Industrial coatings, like Epoxies, MMA,
Polyurethane's, Vinyl Esters, Polyesters, etc. |
|
|
Product #14 Pigmented Mortar -
Replace by
Product #24 |
|
|
Product #15
Chemical Resistant Flooring Resin - a two component,
seamless 100% solids epoxy resurfacing system with High Chemical
Resistance. It may be applied as a coating, or combined with silica sand
or EpoxySystems' multi-colored quartz aggregate to produce a durable,
easy to maintain floor, on both new and old surfaces. |
|
|
Product #16
Epoxy Mortar Resin -
a two-component, 100% solids epoxy resin system, mixed at a 1:1 ratio
by volume. Epoxy Systems’ Product #16, mixed with up to 3 parts dry
EpoxySystems’ Product #75 Filler produces an economical, high-strength
epoxy mortar. Product #16 exceeds the requirements of ASTM C-881-78,
Grade II, Classes A, B & C, Types I & III. Product #16 is recommended
for use in dry environments only. |
|
|
Product #17 Decorative Stone Overlays
- a two component, 100% solids high-mod epoxy adhesive used for bonding
stone and other aggregates in all types of flooring applications. Some
uses would include patios, pool decks, walkways and other areas where a
long wearing and decorative system is desired. |
|
|
Product #18 General Purpose
Epoxy
- a hard set epoxy compound formulated for general use. Product #18
cures at room temperature and is a low viscosity system. This durable,
resilient material requires no post curing to achieve permanent bond
strength. Mixing ratio of 1 to 1 makes this product easy to use. Product
#18 solves many difficult bonding, and epoxy mortar problems. Product
has the ability to bond to a variety of substrates including cannot dry
and hard to dry surfaces. |
|
|
Product #19 Epoxy Mortar -
a multi-function liquid applied, 100% solids epoxy binder and mortar
system with excellent wear, and chemical resistance. Product #19 is an
excellent general purpose material with excellent clarity and color
retention. It is essentially odorless and so it can be used in occupied
areas. |
|
|
Product #20
Epoxy Grout - a moisture
insensitive, two-component, 100% solids epoxy resin system manufactured
specifically for use in temperatures of 40°F and below. It is
recommended for injection or anchor-bolt grouting in the neat state or
as a mortar when mixed with up to 3 1/4 parts of Product #76 -Epoxy
Filler (by volume). PRODUCT #20 exceeds most requirements of ASTM
C-881-90, Types I, Grade 1, Class A. |
|
|
Product #21
Pumpable Mortarcan be used underwater -
a
Pumpable Epoxy Mortar that is a
moisture insensitive, two-component, 100% solids epoxy resin. This
material is specifically designed for use in marine environments, but
can be used in wet or dry strippable form applications. #21 can be
pumped or poured into the void created between the existing structure
and the Epoxy Systems’ Corrosion Free Jacket. Dewatering is not
required. |
|
|
Product #
22 Underwater Epoxy Mortar-Pourable Epoxy Mortar
that is a moisture insensitive, two-component, 100% solids epoxy
resin. This material is specifically designed for use with the Epoxy
Systems’ Fiberglass Systems & Shapes.
Can also be used as self-leveling flooring. |
|
|
Product #23 - Similar to #22 but
in 1:1 mix ratio. Special order only, with minimum quantities required. |
|
|
Product #
24 Pigmented Mortar - is a multipurpose colored
epoxy binder for EpoxySystems’ Mortar Systems This all purpose epoxy
resin is characterized as an excellent general purpose material with
good clarity and color retention. It is essentially odorless and can
therefore be used in occupied areas. |
|
|
Product #
24 Fast Pigmented Mortar - Fast Cure |
|
|
Product #
24 Cold Pigmented Mortar - Cold Temperature Cure |
|
|
Product #25
Epoxy Mortar Kit standard - a 100% solids epoxy
resin and specially selected aggregate system. Units are preproportioned
for ease of mixing and use on the jobsite.
It is
a flowable, self-leveling grout, with handling and physical
characteristics superior to similar grouts. |
|
|
Product #26
Epoxy Mortar Kit - a 100% solids epoxy resin and
specially selected aggregate system which produces a flowable,
self-leveling grout, with handling and physical characteristics superior
to similar grouts. It is designed for floor
resurfacing where high strength and short down time are needed.
Units are preproportioned for ease of mixing and use on the
jobsite. |
|
|
Product #27 Long PotLife Mortar Kit
is a preproportioned 100% solids epoxy resin pack and a blend of special
aggregate. The pot life of Product #27 is 3 times longer than
ordinary epoxy packs; while curing the entire pack, a low exotherm is
produced. |
|
|
Product #28 Epoxy Mortar
- Honey Clear Mortar 4:1 Ratio a multipurpose colored epoxy binder
for EpoxySystems’ Mortar Systems This all purpose epoxy resin is
characterized as an excellent general purpose material with good
clarity and color retention. It is essentially odorless and can
therefore be used in occupied areas. |
|
|
Product #29 Cold
Temperature Cure Mortar i s a specially
formulated binder for cold temperature applications. Able to cure at
temperatures as low as 35°F. They are often used in coolers and food
preparation areas that require constant low temperatures. Product #29
Cold Temperature Cure EPOXY MORTAR is also frequently used in room
temperature applications to meet super-fast cure, limited shutdown
needs. |
|
|
Product #30B Cove Mortar Liquid - Special Order.
Minimum Quantities Required. |
|
|
Product #30A Cove Mortar Powder - Special Order.
Minimum Quantities Required. |
|
|
Product #32 Flexible Epoxy Membrane
is a flexible resin used as an epoxy membrane and as a Product #32
mortar. Epoxy Systems' Product #32 is a two component, 100% solids epoxy
used as a base in many Epoxy Systems' Floor and Mortar Systems. Product
#32 resists cracking caused by horizontal substrate movement, providing
a crack resistant, resilient, sound absorbent, waterproof, durable
floor. Epoxy Systems' Product #32 offers stress-relieving properties for
floor slabs that show movement or vibration. Product #32 is excellent
for use in areas such as mechanical equipment rooms, large animal rooms
and activity centers. |
|
|
Product # 33 Epoxy Block Filler |
|
|
PRODUCT #39 Silane Penetrating
Sealer
is a one component water based silane that provides excellent
protection to concrete surfaces against attack from wet/dry,
freeze/thaw cycles, and de-icing chemicals. PRODUCT #39
imparts a hydrophobic "water-shedding" effect to concrete, masonry,
brick, stone & wood surfaces. The water repellency helps reduce
cracking spalling, chemical degradation, biological growth,
efflorescence, and dirt pick- up. PRODUCT #39 is
easy to use and meets all current VOC regulations. |
|
|
Product #40 - Replaced by
PRODUCT #41 Silane Penetrating Sealer |
|
|
PRODUCT #41 Silane Penetrating
Sealer
is a one (1) component sealer that provides excellent protection to
concrete against attack from wet/dry, freeze/ thaw cycles, and
de-icing chemicals. EPOXYSYSTEMS’ PRODUCT #41 provides a hydrophobic
"water-shedding" effect to masonry surfaces. EPOXYSYSTEMS’ PRODUCT
#41 is a penetrating sealer that is repellent to liquid water but
permeable to water vapor: a "breathable" coating. |
|
|
Product #50 Polypropylene Anti-skid Fine |
|
|
Product #51 Polypropylene Anti-Skid Course |
|
|
Product #52 Polycarbonate Anti-skid Fine |
|
|
Product #53 Polycarbonate Anti-skid Course |
|
|
Product #54 Rubber Anti-skid |
|
|
Product #63
EVA Expansion Joint - a water-tight cross-linked
closed-cell Ethylene Vinyl Acetate expanded foam material that exhibits
unique properties when used in expansion contraction joints. ESI™ a
water-tight cross-linked closed-cell Ethylene Vinyl Acetate expanded
foam material that exhibits unique properties when used in expansion
contraction joints. ESI™ Product #63 is water-tight and exhibits good
chemical resistance properties to most mild non-oxidizing acids,
alkalines and petroleum products. |
|
|
Product #66 Round Quartz Colored Fine
-
a pure silica sand as the basic mineral. Silica is an extremely hard
abrasion resistant and chemically inert mineral, ideal for use in
conditions that - at times - may be severe. Flooring surfaces produced
with high density silica combined with
Industrial Flooring Resins
produced by us consistently show greater
resistance to wear than surfaces filled with minerals or many other
resins or binders. |
|
|
Product #67
Rounded Quartz Colored Medium Aggregates - Similar to
Product #66, but larger. |
|
|
Product #68 Angular Quartz -
Similar to Product #66 but angular. |
|
|
Product #69 50% Benzyl Peroxide (BPO) Powder |
|
|
Product #71 Fumed Silica
Thixotropic Agent |
|
|
Product #72 Grade 000 Silica Aggregate |
|
|
Product #73 Grade 00 Silica Aggregate |
|
|
Product #74 Grade 0 Silica Aggregate |
|
|
Product #75 Silica
Filler is a very clean, specially graded natural
silica aggregate. Product #75 is oven dried just prior to packaging,
this makes it suitable for use in epoxy grouts. When mixed with
Epoxy.com products, Product #75 makes excellent high strength products . |
|
|
Product #76 Epoxy Extender |
|
|
Product #77 Broadcast Sand |
|
|
Product #78 Self leveling filler |
|
|
Product #79 Ground Walnut shell anti-skid aggregate |
|
|
Product #80
Acrylic Sealer -
a clear acrylic solution formulated to create a clear,
non-yellowing protective coating. EPOXY SYSTEMS’ ACRYLIC SEALER provides
a tough, UV and abrasion resistant film that effectively protects
surfaces from moisture penetration, staining, dirt, dust, and wear.
Providing a surface that is easy to clean and maintain, EPOXY SYSTEMS’
ACRYLIC SEALER is an excellent choice for both interior and exterior
applications. |
|
|
Product #81 Epoxy
Gel Extender is a specially formulated blend of fine
granules and plasticizers for use with trowelable (thixotropic) epoxy
materials. |
|
|
Product #82 Mortar Blend Aggregate |
|
|
System #83
Vinyl Ester
- use in a wide range of industrial applications. ESI™ VINYL
ESTER SYSTEMS can be installed as a coating, slurry, or mortar to meet
various chemical and heat resistance needs. |
|
|
Product #84 Universal Primer- Used for
EpoxySystems System #83 and many other EpoxySystems' Products |
|
|
Product #85 Vinyl Ester Mortar |
|
|
Product #86 Vinyl Ester Topcoat |
|
|
Product #87 General Purpose Vinyl Ester |
|
|
EpoxySystems’ Product #100
uses a unique epoxy technology which allows the contractor to
install epoxy systems on new concrete (4-5 days old) without fear of
moisture entrapment. Product #100 Exhibits greater than 100 times
the permeability of standard epoxy slurries and mortars. Product
#100 is used as a base for EpoxySystems’ Chip and Quartz systems and
as a binder for EpoxySystems’ Resinous Mortar Systems, when moisture
is a concern. |
|
|
Product #105 Concrete Catalyst |
|
|
Product #115
Epoxy System
for modifying concrete is a two component, 2:1 ratio, 100% solids,
liquid epoxy resin system. It can be added to conventional concrete or
mortar mixes to produce highfor modifying concrete is a two component,
2:1 ratio, 100% solids, liquid epoxy resin system. It can be added to
conventional concrete or mortar mixes to produce high strength, epoxy
modified concrete or mortar mix. |
|
|
Product #115 Part "C" powder
additive for
Product #115
Epoxy System
- to insure ultimate strength. |
|
|
Product
#120
is a modified latex liquid admixture to improve the bond of Portland
cement concrete toppings, thin-sets, patches, leveling courses,
slush coats, stucco; and to improve the "hang" of vertically applied
flash coats. |
|
|
Product #150 Polyester
Grout is a three component, flowable, fast-setting, 100%
reactive polyester grout specifically formulated for anchor bolt
setting. It may also be used as a grout for floor topping where
chemical resistance is required. |
|
|
Product #201 Oil Stop
Primer
for instances petroleum can penetrate the
surface of a two component, epoxy-amine undercoating designed to be
compatible with petroleum based oil and greases. In many instances
petroleum can penetrate the surface of concrete floors to the extent
that the oil may not be removed by surface cleaning. If untreated,
this oil may migrate back to the surface to cause a delamination. |
|
|
Product
#203 Cold Temperature Cure Polymeric Primer -t is often
used in coolers and food preparation areas that require constant low
temperatures. It is frequently used in room temperature applications to
meet super-fast cure, limited shutdown needs. |
|
|
|
Product
#204
Cold Temperature Cure Polymeric Coating
- is a specially formulated coating for Product #204 Cold
Temperature Cure Polymeric Coating- is a specially formulated
coating for cold temperature applications. Able to cure at temperatures
as low as 35°F. It is often used in coolers and food preparation areas
that require constant low temperatures. It is also frequently used in
room temperature applications to meet super-fast cure, limited shutdown
needs. |
|
|
|
Product #205 Polymeric Flooring Resin |
|
|
|
Product #206 Cold
Temperature Cure Pigmented Polymeric Flooring Resin is a specially
formulated binder for cold temperature applications. Able to cure at
temperatures as low as 35°F. It is often used in coolers and food
preparation areas that require constant low temperatures. Product #206
Cold Temperature Cure POLYMERIC MORTAR is also frequently used in room
temperature applications to meet super-fast cure, limited shutdown
needs. Is available in clear or colors. |
|
|
Product #210 Coal Tar Epoxy
is a two component, 100% Solids coating especially formulated for
high build applications. It produces a tough, flexible, chemical and
impact resistant film. It is formulated to be easily spray applied as
thick as 40 mils in 1 coat. It provides excellent resistance to
aggressive water, acids, and caustics. Suitable for intermittent
exposure to 300 degrees F. |
|
|
Product #211 Polyamide Epoxy Coating -
Ideal for bonding to steel and similar surfaces - Special order only
with larger minimum quantities. |
|
|
Product #212 - Anti-Fouling Coating - Special
orders in quantity only available. |
|
|
Product #213 Decoupage Epoxy is
a two component, 100% solids, epoxy resin system. When mixed at a 1:1
ratio, Product #213 provides a decoupage grade epoxy
surface for wood products.
Product #213 gives a beautiful elegant mar resistant
surface that will enhance the look and value of wood for years to come. |
|
|
Product #214
Tabletop Resin-
an all-purpose, low viscosity Epoxy System for coating wooden counter
tops, tabletops, bar tops and similar applications.
It forms a glossy, hard surface, which is
resistant to stains. It has excellent clarity
and color retention. It is essentially odorless and can therefore be
used in occupied areas |
|
|
Product #215
Epoxy Polyamine
- a high solids, epoxy-polyamide combination, chemical curing, quick-
drying resin system. Product #215 produces a ceramic like coating on
masonry, concrete plaster, cement, asbestos board, wood, fiberglass,
metal and most other rigid materials. Formulated for applications that
require superior adhesion and durability, chemical resistance, corrosive
protection, quick cure and easy cleaning. |
|
|
Product #216 Coal Tar Epoxy
is a two component coal tar epoxy coating, black in color, used to
protect steel, concrete structures, timber, and other construction
materials in corrosive environments. It meets all requirements of Corp.
of Engineers C-200, Federal Specification DOD-P-23236 (SHIPS), and SSPC
16-91. |
|
|
Product #217 Floor Coating Primer |
|
|
Product #218 Floor Coating Intermediate |
|
|
Product #219 Floor Coating Top Coat |
|
|
Product #220 Rebar Touch Up
Epoxy Coating
is a two component, 70% solids epoxy coating specially
manufactured to touch up damage epoxy coated rebar or to coat rebars not
previously protected against corrosion. |
|
|
Product #221 Replaced by
Product #707 Splash Zone & Under
Water Paste |
|
|
Product
#222 Water Based Epoxy- Epoxy Systems’ Product #222
WATER BASED EPOXY COATING is a two component 100% reactive water based
multifunctional epoxy resin coating. Product #222 is manufactured to
produce the utmost in performance in a safe, water borne coating.
Product #222 provides excellent resistance to salt intrusion, and
excellent adhesion to most common construction substrates. |
|
|
P roduct #223
Clear
Water Based Epoxy Curing Compound, Sealer and Bonding Agent
is a two component water based epoxy curing that is used to both cure
and seal concrete and to bond freshly placed concrete to existing
concrete. It is easily pigmented. |
|
|
Product #224 Water Cleanable Epoxy
Mortar Resin is a user friendly, water cleanable, 100%
solids epoxy grout and adhesive. Used for grouting ceramic tile, brick
pavers, and stone, it is supplied in pre-packaged kits containing resin,
hardener, and (in the Product #225 Kit) mineral fillers that produce a
dense, uniform seal. Typical applications for #224 require resistance to
thermal shock, chemicals, and heavy traffic including meat packers,
breweries, canneries, bottlers, CIP areas, and pharmaceutical
formulators. |
|
|
Product #225 Water Cleanable Epoxy
Mortar Kit - includes Product #224
along with the aggregate. Mix the three components together for a ready
to use system. |
|
|
Product #226Fast Setting
Water Based Epoxy is a Fast Setting Water Based Epoxy
Coating is a two component, 100% reactive, water based, multi functional
epoxy resin coating. PRODUCT #226 is manufactured to produce the utmost
in performance in a safe, water borne coating. PRODUCT #226 provides
excellent resistance to salt intrusion, and excellent adhesion to most
common construction substrates. Product #226 is VOC Compliant, Fast
Curing, and tintable with standard colorants. It is Internally
Flexibilized so it can be applied to metals and plastics. It is
water-reducible and easily applied. Special order item only.
Requires a minimum quantity. Contact
EpoxySystems' Tech Support for
details.
|
|
|
|
|
Product #250 Water Tank Type
Coating is a 100% solids, moisture- insensitive epoxy
coating, containing no solvents. It is mixed at a 2:1 ratio, produces a
tough, chemical and abrasion-resistant coating for dry or damp concrete,
wood or steel surfaces. |
|
|
Product #255 Mastic High
Build Epoxy Coating is a 100% solids,
moisture-insensitive, epoxy resin system. When mixed at a 1:1 ratio, by
volume, it produces an excellent coating for dry or damp concrete, wood
or steel surfaces. It iss used on piles, piers, and concrete or steel
tanks where concrete or steel needs to be protected from abrasive
environments. |
|
|
Product # S-255 - Solvent for thinning
EpoxySystems' Product #255 |
|
|
Product #256 Impact and
Chemical Resistant Epoxy Coating. is a 100% solids epoxy
coating specifically formulated and manufactured to produce a tough,
impact resistant coating |
|
|
PRODUCT #260 Corrosion
Resistant Epoxy Protective Primer and Coating
are two-component, 100% solids epoxy coatings based on multi-functional
high performance resin and anti-corrosive pigment. PRODUCT #260 is used
as a two coat system. PRODUCT #260 provides corrosion resistant
protection to steel and other metals. PRODUCT #260 has excellent
resistance to chemicals up to 300°F, and hot water resistance at
temperatures up to 250°F under continuous immersion. PRODUCT #260 is
formulated in a convenient 2 to 1 ratio, by volume mix ratio and has a
long pot life to simplify application. The primer is green and the
topcoat is blue. (Other colors are available as special order product.)
PRODUCT #260 is particularly effective in applications which entail
force curing, either as pre-immersion or during immersion service. |
|
|
Product #300 3.5:1 Injection Resin -
This product is an injection resin with a 3.5:1 mix ratio, designed to
be backwardly compatible with certain older designs of injection
machines. See the products 301 to 306 below for 2:1 mix ratio injection
resins. |
|
|
Product #3012:1Injection
Resin, low Modulus - a 100% solids low viscosity epoxy
adhesive used to restore cracked structural concrete by the pressure
injection method and to grout cracks in a horizontal plane by gravity. |
|
|
Product #301SC a longer Potlife
version of
Product #301 |
|
|
Product #301Cold a faster version of
Product #301 typically used in
Cold Temperature Cure applications, or where a very fast set is needed |
|
|
Product
#302 Injection a 100% solids low viscosity
moisture insensitive epoxy adhesive used to restore cracked structural
concrete by the pressure injection method and to grout cracks in a
horizontal plane by gravity. |
|
|
Product #303
Low Viscosity a is a two component, 100% solids, moisture
insensitive epoxy resin system, mixed at a 2:1 ratio, with a viscosity
of light-weight oil. Product #303 exceeds the requirements of ASTM C 881
87, Types I, II, Grade 1, Class "B" and "C". Use neat for grouting damp
and dry cracks or as a penetrating sealer on concrete, and wood. May
also be mixed with Special Fillers (Products #72-75), to create epoxy
mortars. |
|
|
Product #304 Injection Resin and
Mortar Binder
is a moisture insensitive, two-component, 100% solids epoxy resin
system designed specifically for use in temperatures of 40°F and below.
It is recommended for injection or anchor-bolt grouting in the neat
state or as a mortar when mixed with up to 3 1/4 parts of PRODUCT #75
Filler (by volume). PRODUCT #304 exceeds requirements of ASTM C-881-90,
Types I, Grade 1, Class A. |
|
|
Product #305 Injection Resin
200 CPS - Epoxy.com Products #305 and Product #306 are
two-component, low viscosity, 100% solids epoxy resin base adhesive.
Modified Bisphenol A-Epichlorohydrin epoxy resin and Amido-amine type
hardener, modified to be compatible with damp concrete. Product #305 has
a Potlife of 1 hour at 77° F (25° C). |
|
|
Product #306 Injection Resin
is a fast version of Product #305. Product #306 has a pot life of
5-10 minutes at 77° F (25° C) |
|
|
Epoxy.com PRODUCT #312 Aliphatic
Sprayable Polyurea Coating
is a two component sprayable aliphatic polyurea. It dries in seconds to
provide a tough chemical and abrasion resistant coating. As an aliphatic
polyurea, PRODUCT #312 is color fast and will resist
yellowing from Ultra violet light exposure. Typical working times of one
minute or less can be expected. This fast reaction requires a fast,
efficient mixing technique so that the mixture can be applied within the
short gel times. Impingement mixing from available two-component spray
machinery is efficient and entirely adequate. |
|
|
Product #314 Under Water Coating |
|
|
Product #315
Chip Flooring Product #315 is a seamless, plural component,
liquid applied, 100% solids polymeric colored flake floor resurfacing
system with superior wear, and chemical resistance. Product #315 with
"multi-colored" flakes
produces a durable, easy to maintain floor, on both new and old
surfaces. |
|
|
Product #315BC Polymeric
Coating and Base Coat for the
315Chip Flooring System. It can also be used as a
stand alone coating. If Epoxy.com Product #315BC is used as a stand
alone coating over concrete, it is recommended that you first prime with
Product #889 Primer. |
|
|
Product #315BC - Fast Same as
Product #315BC
Polymeric Coating for Base Coat
for the 315Chip Flooring System
, but with a fast cure. |
|
|
Product #315BC-Cold Same as
Product #315BC
Polymeric Coating for Base Coat
for the 315Chip Flooring System
, but with a cold temperature cure. |
|
|
Epoxy.com #315NH is a 100%solids, moisture-insensitive epoxy
coating. Epoxy.com #315NH mixed at 2 :1 by
volume ratio, produces an excellent coating for dry or damp concrete,
wood, or steel surfaces. Epoxy.com #315NH is available in
a summer grade and winter grade formulation. It can be used as a
stand alone coating or as a base coat for Epoxy.com
chip floor. It can also be used to replace
Product #315BC Polymeric
Coating when a non-hazmat to ship basecoat is required.
|
|
|
Product #316 Fast
Set Flooring -
a 100 % solids fast setting two-component epoxy resin system.
Is made to set fast even in temperatures below freezing. It is
recommended for flooring, injection or anchor-bolt grouting in the neat
state or as a mortar when mixed #75 Filler
.
It exceeds most requirements of ASTM C-881-99,
Types I and IV , Grade 1, Class A. |
|
|
Product #340 Colored Chips forChip
Flooring |
|
|
Product #370 Replaced by
417 Elastomeric Waterproofing Horizontal Grade |
|
|
Product #371 Replaced by
417 Elastomeric Waterproofing
Vertical Grade |
|
|
Product #372 Black Waterproofing Membrane Knife
Grade |
|
|
Product #373 Replaced by
417 for Potable Water |
|
|
Product #374 Replaced by
419 Waterproofing Membrane |
|
|
Product #376 - Membrane below thin-set and tile |
|
|
Product #390
Flexible Acrylic Roof Coating -designed to be a highly durable,
flexible roof coating with outstanding resistance to weathering,
ultra-violet light and water. Withstands ponding water conditions. It is
suitable for application over sprayed urethane foam insulation roofs,
concrete, wood or asphalt roofs. It serves as an excellent protection
for urethane foam insulated storage tanks, grain elevators, etc. |
|
|
PRODUCT #400
Chemical Resistant Urethane is a two component, chemical resistant,
polyurethane coating. The high gloss finish offers excellent abrasion
resistance, chemical and stain resistance, and superior color
retention. It can be used equally well on vertical or horizontal
surfaces. It is ideal for concrete floors. It is used as a finish
coating option for most EpoxySystems’ Flooring Systems. |
|
|
Product #401 Replace by EpoxySystems'
Product 458. |
|
|
Product #402 - Replace by
EpoxySystems'
Product #458 |
|
|
Product #403 Urethane Coating Aliphatic |
|
|
Product #404 Fast Cure Urethane Membrane |
|
|
Product #405 Fast Cure Urethane Topcoat. |
|
|
Product #407 Aliphatic Traffic Bearing
Membrane
is a two component, ultra high solids aliphatic polyurethane elastomeric
membrane. When applied, it is resilient and accommodates movement in
concrete substrates. Epoxy.com Product #407 is used as a top coat
traffic bearing membrane or non-skid coating that retains color and
physical properties when exposed to harsh UV conditions. Epoxy.com
Product #407 is used as a system with Epoxy.com Product #882, and may be
applied as the top coat on Epoxy.com Product #409
to maximize cost effectiveness. Epoxy.com Product #407 cures at ambient
temperatures and is impermeable to moisture, oils, mild acids, gasoline,
and alkalies. |
|
|
Product #408 is a black,
liquid applied, single-component, moisture-cured 100% solids,
polyurethane waterproof coating, designed to form a low odor, seamless,
flexible rubber membrane impervious to moisture.
|
|
|
409 Traffic Bearing Membrane
is a Resilient Traffic Bearing Membrane
is a 100% solids, ambient cure impermeable elastomer.
PRODUCT #409 is resistant to moisture, oils, mild acids,
gasoline, and alkalies.
PRODUCT #409 when applied to concrete or other surfaces, is
resilient and accommodates movement in concrete substrates.
PRODUCT #409 is used as a traffic bearing membrane or non-skid
coating that retains color and physical properties when exposed to harsh
UV conditions. |
|
|
Product #410 replaced by
409 Traffic Bearing Membrane |
|
|
Product # 415 Elastomeric Membrane now called
Product #452 Polyurethane Membrane Standard |
|
|
Product #416
Polyurethane Coating a moisture-cured, liquid applied,
polyurethane, based on Aliphatic Isocyanides in combination with
additives and pigments to produce a wear resistant, protective and
decorative floor coating, for interior and exterior applications. It is
primarily used as the protective topcoat of the
450 and
450X2 deck coating systems, but when used with the proper primer,
can be used as a stand alone coating. |
|
|
Product #417
Elastomeric Waterproofing A black, liquid applied
single-component moisture-cured polyurethane coating, designed to form a
seamless, flexible rubber membrane impervious to moisture. CompositioA
black, liquid applied single-component moisture-cured polyurethane
coating, designed to form a seamless, flexible rubber membrane
impervious to moisture. Composition: Polyurethane elastomer. A
two-component system is available, which does not depend on atmosphere
moisture to cure. Type I: For horizontal surfaces. Type II: For vertical
surfaces. USES: allows expansion and contraction over a broad
temperature range and maintains waterproofing properties under
continuous exposure to water. Type II has a thixotropic consistency and
may be used on vertical as well as horizontal surfaces. 417 remains
flexible from -75°F to +175°F (-59°C to 79°C). Use as a waterproof
membrane is intended for use wherever overflow water must be contained
. |
|
|
Product #417PW for Potable Water
is similar to #417 Elastomeric
Waterproofing
, but meets potable water standards |
|
|
Product #418 Elastomeric Membrane,
a black, self-leveling, liquid applied, two-component polyurethane
system, designed to form a tough rubber membrane impervious to moisture.
Type I: For horizontal surfaces Type II: For vertical surfaces.
Composition: Polyurethane elastomer. A two-component system, which does
not depend on atmosphere moisture to cure. Basic Uses: Once cured, #418
allows expansion and contraction over a broad temperature range and
maintains flexibility and waterproofing properties under continuous
exposure to water above or below grade. PRODUCT #418 has a thixotropic
consistency and may be used on vertical as well as horizontal surfaces.
PRODUCT #418 remains flexible from -75° to 175°F. |
|
|
Product #419 Waterproofing
Membrane Black Waterproofing Industrial Strength is
a black, liquid applied, two-component, high solids, chemical cured,
polyurethane coating designed to form a tough rubber membrane impervious
to moisture. Composition: Polyurethane elastomer. A two-component system
which does not depend on atmospheric moisture to cure. Basic Uses: Once
cured, #419 allows expansion and contraction over a broad temperature
range and maintains flexibility and waterproofing properties under
continuous exposure to water above or below grade. It has a thixotropic
consistency and may be used on vertical as well as horizontal surfaces.
The #419 waterproof membrane is intended for use on steel, wood,
concrete, asphalt, tanks, ponds, roofs, foundations, etc. |
|
|
Product
#420 Urethane Injection or moisture.EpoxySystems’ Product
#420 reacts with water and expands to form an impermeable HYDROPHOBIC
barrier. When reacted and hardened, EpoxySystems’ Product #420 is
insoluble to water and other aggressive chemicals. |
|
|
Product #421 Urethane Injection resin |
|
|
Product #422
Replace by Product #420 Urethane Injection resin flexible |
|
|
Product #423 Urethane Injection resin
|
|
|
PRODUCT #424 is a rigid two component
closed cell foam impervious to water and moisture. It can
be used where structural foam is needed to encapsulate waste or restore
the physical properties of timber and other masonry materials. |
|
|
Product #425
is a two component, HCFC-141b/water co-blown rigid polyurethane foam
system designed for low-density insulation applications. PRODUCT #425 is
typically used for floatation (Boat Foam) inside fiberglass parts. It
bonds well to metals, wood and some plastics. This foam system meets
Military Specification P-21929B. |
|
|
Product #426 Urethane Gel |
|
|
Product #427 Urethane Cleaner |
|
|
Product #428 Urethane Safety Cleaner |
|
|
EpoxySystems’ Product #429
Urethane Injection Resin Accelerator is specifically formulated to
increase the cure rate of EpoxySystems’
Product #4 Urethane Injection Resin. The accelerator liquid is
normally used to compensate for cold weather or cold water temperatures. |
|
|
System #430 Elastomeric Multi-Colored
Decking System is a l iquid-applied, single-component,
moisture-cured, polyurethane deck covering system. For waterproofing
patios, sundecks, stairways, balconies, etc. Product #430
can be used on all decks where a skid-resistant, long-lasting,
wear-resistant, water-proof surface is required. It may be used on new
decks as well as on old concrete decks which are damaged, or cracked.
The system is suitable for exterior as well as interior applications in
all kinds of climates. The coating retains its elastomeric properties in
below freezing weather as well as in very hot climates. |
|
|
EpoxySystems’ PRODUCT #431
is a two component, flame retardant foam especially manufactured to
provide a rigid foam with physical properties similar to that of timber
or cement grouts, at a convenient one to one ratio, A to B, light black
in color.
Product #431 will bond to wet, moist or dry surfaces, even to
Plexiglas, with no shrinkage and ample pot life after mixing A & B
components. |
|
|
Epoxy.com Product #432 is a low
viscosity, rapid gelling, hydrophobic grout. Epoxy.com Product #432 is
used to seal leaks in cracked concrete, for soil stabilization and for
repairing leaking joints in structures. This all-purpose grout is easily
mixed with water or stabilizer at a convenient 1 to 1 by volume mix
ratio |
|
|
Product #440 Light Stable Deck Membrane |
|
|
EpoxySystems' Product # 441
is a two component water-based aliphatic (non-yellowing)
polyurethane. It is free of the health and environmental problems
normally found in solvent-based urethanes, while maintaining excellent
performance properties. Product # 441 polyurethane
provides a matte finish. Product # 441 has good
chemical, stain, and mar resistance. In addition, it’s easy to clean and
has excellent color retention under heavy foot traffic. It is a high
performance coating for use in a variety of seamless floor and wall
coating systems. Product # 441
eliminates the strong solvent odor normally associated with many high
performance materials. It’s ideal for topcoats and finishes that require
high abrasion resistance. Typical application areas are clean rooms,
hospitals, pharmaceutical facilities, stained concrete, wood floors, and
as a seal coat for most Epoxy Systems, Inc. floor and wall coating
systems. |
|
|
#450 Elastomeric
Flooring system provides a waterproof, elastomeric,
traffic bearing deck coating. It is a monolithic system that
incorporates excellent adhesion, flexibility, impact, abrasion
resistance, and chemical resistance. Petroleum products or cooling tower
water spillage have little or no effect on the coating. Physical
stresses imposed by vibration of equipment will not cause delamination
or rupture of the coating. The elastic properties of all system
components enable the complete system to give and work with all but the
most unusual movement of the floor or deck. |
|
|
System
#450 Mechanical Room Flooring System -
Liquid-applied, single-component, moisture-cured, polyurethane deck
covering system. 450MR system provides a waterproof, elastomeric,
traffic bearing deck coating. It is a monolithic system that
incorporates excellent adhesion, flexibility, impact, abrasion
resistance, and chemical resistance. Physical stresses imposed by
vibration of equipment will not cause delamination or rupture of the
coating. The elastic properties of all system components enable the
complete system to give and work with all but the most unusual movement
of the floor or deck. |
|
|
System
#450X2 Urethane Decking Systemdouble strength is an
elastomeric coating system for walking decks, balconies, patios, etc.,
where an absolutely waterproof coating is crucial, such as above living
quarters and any other occupied areas |
|
|
System #450HT- High Tensile Strength version of the 450 system for
extra heavy duty applications |
|
|
|
|
Product #451
Aromatic Polyurethane Coating -
is an aromatic, liquid applied, single-component, moisture cured
polyurethane floor coating for use in indoor applications such as
industrial plants, mechanical rooms, and locations where surfaces must
withstand pedestrian traffic |
|
|
Product #452
Polyurethane Membrane Standard is a liquid applied,
single component, moisture-cured polyurethane. It is the major component
of all EPOXYSYSTEMS’ PRODUCT #450 deck coating systems. |
|
|
Product #453 Elastomeric Mortar-
is a sloping system using an elastomeric binder adhesive mixed with
aggregate for sloping decks, based on polyurethane elastomers. |
|
|
Product
#454 LVOC Polyurethane Membraneis
a liquid-applied, single component, aromatic, moisture-cured
polyurethane which will not blister or gas. It may be substituted for
our Epoxy.com Product #452.The
Epoxy.com 454 LVOC Non-gassing Low VOC waterproofing membrane
used with the all Epoxy.com 430 and 450 Series systems.
Epoxy.com 454 LVOC Non-gassing may be used to fill minor
cracks in concrete, except for expansion joints where Epoxy.com
Product #910 is recommended. |
|
|
Product #455 Polyurethane Membrane Grading Material |
|
|
Product #456 Urethane Coating |
|
|
Product #457 Polyurethane Membrane 100% Solids |
|
|
Product #458
2Component Urethane Coatingis a liquid-applied,
two-component, catalytic cured polyurethane floor and wall coating for
use in air fields, industrial plants, stores, and other locations where
surfaces must withstand heavy use of foot traffic. It provides a durable
finish that protects floors against occasional chemical spillage, dirt,
grease and oil. It gives industrial floors a well maintained look while
retaining a glossy appearance. Dusting of concrete floors is eliminated
when the surface is sealed with PRODUCT #458 and, as dirt and oils are
prevented from penetrating the concrete, detergent and water easily
clean the floor. PRODUCT #458 in pigmented form may be used on floors
to hide an unsightly appearance of the substrate or to provide a
reflective, bright appearance that will lighten up a warehouse,
highlighting work areas and traffic lanes. |
|
|
Product #460 Polyurethane Membrane and
Coatingis a two component, aliphatic, 100% solids, Zero
VOC, elastomeric, traffic coating system for walking deck surfaces.
Concrete or Plywood substrates. For waterproofing walking decks,
balconies plazas, parking decks, mechanical room floors, etc. Designed
for pedestrian and vehicular traffic. |
|
|
Product #462 High Tensile Strength Urethane Deck
Membrane |
|
|
Product #466 High Tensile Strength Aliphatic Top
Coating |
|
|
Product #469 Elastomeric Membrane Deck Grade |
|
|
System #470 Multi Use
Elastomeric System |
|
|
Product #471 Multi Use Base Coat |
|
|
Product #472 Multi Use HT |
|
|
Product #473 Aromatic Urethane Coating for #470
System |
|
|
Product #474 Aliphatic Urethane Coating for #470
System |
|
|
Product #475 Catalyst for #470 System |
|
|
System #480 Elastomeric Deck |
|
|
Product #490 Athletic and Driveway
Surface
is a one part liquid applied coating with good ultraviolet
light resistance. PRODUCT #490 is designed for use on pool decks, tennis
courts, asphalt driveways, and concrete surfaces. This product is
recommended for foot traffic areas to reduce slipping on commercial and
industrial floors. Due to the waterbased formulation of the product, it
can be installed in areas where solvent based coatings are objectionable
due to their odors and fire hazards. This material can also be applied
over damp as well as dry surfaces |
|
|
Product #500 Polyester Wood
Filler Pine is a two component, wood like polyester
filler paste. Quick setting and easy to use. EpoxySystems' Polyester
Wood Filler is designed primarily for wood repairs in construction
surfaces. Can be used to fill areas of deteriorated concrete (or holes).
Also used by model shops for making permanent repairs, fillets, and
design changes in the construction of all wood models and patterns.
EpoxySystems' Polyester Wood Filler has excellent adhesion to wood,
fiberglass, and plaster and can be worked with standard woodworking
tools in a quick and convenient manner. |
|
|
Product
#501 Polyester Wood Filler Mahogany is a two
component, wood like polyester filler paste. Quick setting and easy to
use. EpoxySystems' Polyester Wood Filler is designed primarily for wood
repairs in construction surfaces. Can be used to fill areas of
deteriorated concrete (or holes). Also used by model shops for making
permanent repairs, fillets, and design changes in the construction of
all wood models and patterns. EpoxySystems' Polyester Wood Filler has
excellent adhesion to wood, fiberglass, and plaster and can be worked
with standard woodworking tools in a quick and convenient manner. |
|
|
Product #502 Polyester Wood Filler Hardener 1 oz. |
|
|
Product #503 Polyester Wood Filler Hardener 4 oz. |
|
|
Product #504
Polyester Paste
Gray is a
fast-setting industrial filler paste used for manufacturing, fabrication
and repair in aircraft, aerospace and other industries having
requirements for above normal temperature exposure. Fast and permanent
applications are achieved by POLYPASTE. The service temperature of
Filler 7 is up to 400 degrees F (205 degrees C). It is used in the
construction industry to seal cracks for injection and for patches used
on concrete, wood, steel and other suitable construction materials.
Excellent machining and finishing results are accomplished by grinding,
sanding, scraping, etc. When exposed to elevated temperatures, POLYPASTE
has a tendency to darken but does not gas, bubble, or cause any finish
distortion. This product does not contain wax and readily bonds to
itself and other substrates such as FRP/SMC, hi-temp epoxy molds,
aluminum, steel, cast iron, urethane foam parts, etc. POLYPASTE is
non-metallic, non-conductive, and non-sparking. |
|
|
Product #505
Polyester Paste Black is
a fast-setting industrial filler paste used for manufacturing,
fabrication and repair in aircraft, aerospace and other industries
having requirements for above normal temperature exposure. Fast and
permanent applications are achieved by POLYPASTE. The service
temperature of Filler 7 is up to 400 degrees F (205 degrees C). It is
used in the construction industry to seal cracks for injection and for
patches used on concrete, wood, steel and other suitable construction
materials. Excellent machining and finishing results are accomplished by
grinding, sanding, scraping, etc. When exposed to elevated temperatures,
POLYPASTE has a tendency to darken but does not gas, bubble, or cause
any finish distortion. This product does not contain wax and readily
bonds to itself and other substrates such as FRP/SMC, hi-temp epoxy
molds, aluminum, steel, cast iron, urethane foam parts, etc. POLYPASTE
is non-metallic, non-conductive, and non-sparking. |
|
|
Product #540 replace by
Product #702 |
|
|
Product #541 Polyester Anchor Bolt Adhesive |
|
|
Product #550 Rapid Setting Trowel mortar |
|
|
Product #551 Thin Patch |
|
|
Product #600
Flexible Novolac is a two-component, 100% solids epoxy
coating based on multi-functional high performance flexibilized resin.
PRODUCT #600 provides corrosion resistant protection to steel, other
metals and concrete. It has excellent resistance to chemicals up to
300oF. It is resistant to continuous immersion in water up to 212oF .
PRODUCT #600 is formulated in a convenient 1 to 1 ratio, by volume mix
ratio and has a long pot life to simplify application. PRODUCT #600 is
more effective in applications which entail force curing. |
|
|
Product #630
Novolac Coating/Mortar Binder
-
a 100% solids epoxy Novolac ideal for harsh chemical and solvent
resistant applications. It is ideal for use as a troweled mortar, slurry
binder, and coating for concrete and steel in extremely corrosive areas
where resistance to 98% sulfuric acid or other strong caustics is
needed. It is ideal for use as a protective coating for concrete and
steel in the extremely corrosive areas of chemical plants and pulp mills
secondary containment areas, water and waste treatment, and gas and
electric utilities. |
|
|
Product #632 Novolac Control Joint
Filler is a 100% solids flexible Novolac epoxy
Chemical Resistant joint filler for saw-cut joints of concrete slabs on
grade. |
|
|
Product
#633 Novolac Coatingis a 100% solids epoxy Novolac
coating ideal for harsh chemical and solvent resistant applications.
Itis used in secondary
containment, solvent storage, pump pads, trenches, and other high
exposure areas. Itis ideal for use as a protective coating for concrete
and steel in the extremely corrosive areas of chemical plants and pulp
mills secondary containment areas, water and waste treatment, and gas
and electric utilities.
Product #633 is commonly used as a seal coat for
EpoxySystems' MORTAR SYSTEMS where chemical resistant
performance is required. |
|
|
Product
#634 Novolac High Temperature Epoxy - is a 100%
solids amine cured epoxy Novolac that is solvent free. Suitable for
immersion and non-immersion service particularly in aggressive acid and
alkali environments with elevated temperatures. Epoxy Systems
Product #634 produces a tough, chemical resistant coating
on concrete, iron and non-iron surfaces. As a low viscosity epoxy
Novolac it is suitable for hand or spray application. |
|
|
Product
#635 Novolac Coating/Mortar Binder is a high solids
epoxy Novolac coating ideal for severe chemical and solvent resistant
applications.
It is filled with treated
ceramic filler to provide improved chemical and thermal shock
resistance. Itis ideal for use as a protective coating for concrete and
steel in the extremely corrosive areas of chemical plants and pulp mills
secondary containment areas, water and waste treatment, and gas and
electric utilities.
EpoxySystems' Product #635 is commonly used as a seal
coat for EpoxySystems' MORTAR SYSTEMS where chemical
resistant performance is required.
|
|
|
Product
#636 High Temp Chemical Resistant Primer/Topcoat-
a 100% solids amine cured epoxy Novolac that is solvent free.
Specifically designed as a Methanol resistant coating. Product #635 is
well suited for use in a wide array of aggressive acids, alkalies and
organic solvents. It produces a tough, chemical resistant coating on
concrete, iron and non-iron surfaces. As a low viscosity epoxy Novolac
it is suitable for hand or spray application. |
|
|
Product #637
High Temp Coating/Primer is a
100% solids amine cured epoxy Novolac that is solvent free. Suitable for
immersion and non-immersion service particularly in aggressive acid
environments.
Epoxy Systems Product #637 produces a tough, chemical
resistant coating on concrete, iron and non-iron surfaces. As a lower
viscosity epoxy Novolac it is suitable as a primer or as a top coating.
Excellent against 98% Sulfuric Acid. |
|
|
Product #638 Glass Filled Novolac |
|
|
Product #640
Chemical & Heat Resistance is a two component; 100% solids
brush, roll or airless spray applied coating designed to provide
cavitation, corrosion and erosion resistance to concrete, metallic and
nonmetallic surfaces. PRODUCT #640 acts as an inert barrier against
extremely harsh environmental factors such as low and high PH,
temperature extremes, dry and fluid particulate flow and corrosive
chemical attack. |
|
|
Product #641High
Temp Epoxy is a moisture-insensitive, two-component,
100% solids epoxy coating. It is especially formulated to protect
concrete, steel and wood subject to high temperatures and corrosion. |
|
|
Product #641LV High Temp Resistant
Mortar
is a two component highly cross-linked novolac epoxy resin
system. It is especially formulated to be used as a high temperature
grouting or laminating resin. It is used to protect concrete, steel and
other substrates from high temperatures and corrosion. |
|
|
Product #642
Multifunctional High Chemical Resistance Epoxy
Coating/Bonder
is a two component, 100% solids, one coat trowel grade or grout pump
applied protective coating designed to provide cavitation, erosion and
corrosion resistance to metallic and non-metallic surfaces. Product #642
acts as a barrier against extremely harsh environmental factors such as
low and high PH, temperatures extremes, dry and fluid particulate flow
and corrosive chemical attack. |
|
|
PRODUCT #643 Highly
Chemical Resistant Coating is a solvent free, high
functionality Novolac epoxy coating suitable for immersion and
non-immersion service. Designed specifically as a Methanol resistant
coating. It is well suited for protection in a wide array of aggressive
acids, alkalies and organic solvents. It produces a tough, chemical
resistant coating on ferrous and non-ferrous metals and concrete. |
|
|
Product #644 High Temp Chemical Resistant Coating.
Similar to 641LV, but with fillers to make it
thicker. |
|
|
648 Chemical Resistant Coating
is a two component high performance epoxy resin formulated with a
convenient 1 to 1 mix ratio. EPOXYSYSTEMS’ PRODUCT #648 Chemical
Resistant Coating has been developed as a coating for exposure to
organic acids and other severe chemical environments. It is used widely
in the food and chemical industries for protection of concrete, wood,
and steel. EPOXYSYSTEMS’ PRODUCT #648 is suitable for application by
brush, roller or spray. Where in-shop production techniques may be
utilized and elevated temperature curing is feasible, rapid property
development may be achieved by curing at 200 - 250°F (93 - 121°C). This
will provide a cured film which may be handled within a relatively short
period of time (about 4 hours). Elevated temperature curing will also
enhance ultimate physical and chemical resistant properties. |
|
|
Product
#650 Resurfacing Grade Epoxy Ceramic Filled Epoxy Coating |
|
|
Product #651 Ceramic
Filled Epoxy Mortar is a two-component, 100% solids,
ceramic reinforced, trowelable polymeric compound which can be used to
repair virtually any metal surface that has been damaged by
erosion/corrosion, cavitation or abrasion. |
|
|
Product
#652 Metal Filled Trowel Grade Epoxy - a
two-component, 100% solids, metal-reinforced polymeric compound which
can be used to repair virtually any metal surface that has been damaged,
cracked or worn. |
|
|
Product #653 Emergency Epoxy Liquid Grade |
|
|
Product #654 Metal Filled Internally lubricated
Trowel Grade |
|
|
Product #669 Strait Vinyl Ester Resin |
|
|
Product #670
Vinyl Ester General Purpose
is formulated from a vinyl ester, low viscosity resin of 100% reactive
solids in a composite with inorganic fiber reinforcement. It provides
the ultimate in chemically resistant properties to prevent deterioration
where reactive chemicals exist |
|
|
Product #671
Conductive Primer/Sealer
- EpoxySystems’ Product #671 is a low viscosity, two component, carbon
filled, polyamide modified conductive primer/sealer formulated with
special wetting agents to provide maximum penetration into concrete
surfaces. Product #671 is ideal for both new and old concrete surfaces.
Product #671 provides excellent resistance to wear, and can be used
either alone or as a conductive sealer or as a conductive primer when
used with EpoxySystems’ product #674 Electro-Static Dissipating Urethane
Topcoat and EpoxySystems’ Conductive Systems. |
|
|
Product #672 Conductive Epoxy
is a two component, 100% solids epoxy/aggregate material that utilizes
the latest in conductive floor technology. Epoxy Systems' CONDUCTIVE
EPOXY can be installed as a coating or as a component to Epoxy Systems’
Flooring Systems. It can also include Epoxy Systems
ELASTOMERIC MEMBRANES to produce
waterproof, crack resistant Systems. Typical Uses of include:
Ammunitions Facilities, Paint and Solvent Storage Areas,Electronic
Component Plants Hazardous Materials Storage Areas |
|
|
Product #673 Conductive Terrazzo |
|
|
PRODUCT #674 - Electrostatic
Dissipative Urethane Coating is a two component, Electro
Static Dissipative chemical resistant, polyurethane coating. The high
gloss finish offers excellent abrasion resistance, chemical and stain
resistance, and superior color retention. EPOXYSYSTEMS’ PRODUCT #674 can
be used equally well on vertical or horizontal surfaces. It is ideal for
concrete floors and walls in warehouses, storage facilities, aircraft
hangars, animal housing, and vehicle maintenance facilities. Available
in both clear and pigmented formulations, EPOXYSYSTEMS’ PRODUCT #674 is
used as a finish coating option for most EpoxySystems’ Flooring Systems. |
|
|
Product #675 Electrostatic Dissipating
Water Borne Epoxy Topcoat-a pigmented, water emulsion
epoxy electro-static dissipative finish designed to have maximum
penetration into concrete surfaces to provide high bond strength and
adhesion. It has very low odor and can be used in occupied areas as a
finish sealer in Thin-Film Electro-Static Dissipative Coating Systems. |
|
|
Product #680 MMA
Polymer Concrete is a Polymer Concrete methyl
methacrylate (mma) reactive resin is used as a binder to develop polymer
concrete which produces extremely high strength and chemical resistance
with an abrasion resistant surface. It is prepackaged and
preproportioned for easy mixing and placing at the job site. The liquid
polymer and the preproportioned hardener filler is mixed either in the
polyethylene bag or in a mortar mixer. |
|
|
Product
#681
MMA Primer and Sealer for
MMA Polymer Concrete |
|
|
Product #685 MMA Crack Healer
and Sealer
is for injection repair or as a penetrating crack repair and sealer
on concrete. It is a two component Methyl Methacrylate resin system that
polymerizes in place. The extremely low viscosity will penetrate into
concrete cracks as fine as 0.003 inches. |
|
|
Product #690 All Purpose MMA Primer and Mortar |
|
|
Product #701
Flexible Bonder
-
a two component, 100% solids, mixed
at a 1:1 ratio adhesive formulated to give a permanent bond to ceramic,
metal, concrete and elastomeric surfaces. It
is thixotropic, non-sag, and is easily applied by trowel. |
|
|
Product #702 Traffic Marker and Anchor Bolt Adhesive
is a two component, 1:1 ratio, 100% solids, moisture insensitive epoxy
resin system manufactured to bond delineators and traffic markers to
median barriers, parapets, and roadways. It is a normal setting adhesive
for use in temperatures above 50° F. PRODUCT #702 will bond to steel,
concrete, and asphalt. It exceeds the requirements of AASHTO M237 Type
IV. |
|
|
Product #703
Flexible Gel Adhesive is a
non-sagging material that is ideal for repairs on vertical or overhead
surfaces. It exceeds the requirements of ASTM C 881-87, Types I, II, and
III Grade 3, Class "B", "C", "E" and "F".
|
|
|
Product #704 Emergency Epoxy
- is a rapid setting, two
component, 1:1 ratio epoxy adhesive. It sets in six minutes and can be
put into service in one hour regardless of temperature. It was designed
to bond metals, glass, concrete and wood in a matter of minutes
. |
|
|
Product #706
Heat Resistant Bonder/Mortaris
a 100% solids, moisture insensitive epoxy adhesive and repair material.
When A and B Components are mixed they produce a gel consistency similar
to petroleum jelly, which will not sag or run on a vertical or overhead
surface application. |
|
|
Product #
707 Splash Zone & Under Water Epoxy Paste is a
moisture-insensitive, two-component, 100% solids epoxy-resin system.
When mixed at a 1:1 ratio, by volume, this product produces a paste-like
material that is ideal for protection or restoration of concrete, steel
and timber piles and other structural elements in marine environments. |
|
|
Product #710 Superseded by
EpoxySystems' Product #225 |
|
|
|
|
Product #711 is protective
coating designed to provide cavitation, erosion and corrosion resistance
to metallic and non-metallic surfaces. Product #711 acts as a barrier
against extremely harsh environmental factors such as low and high PH,
temperatures extremes, dry and fluid particulate flow and corrosive
chemical attack. |
|
|
Product #712 a two component flexible sealant,
formulated to repair leaking electrical equipment and circuit breakers.
It bonds tenaciously to ceramics, plastics, metals and most substrates. |
|
|
Product #713 Dowel Bar and Anchor Bolt
Adhesive is a two component, thixotropic, fast setting
epoxy adhesive. It is specifically formulated with an easy to use, non
sag consistency. The special high function resin system allows cure in
temperatures as low as 20 F. The non-sagging properties will permit the
material to be pumped or gunned into horizontal holes for anchoring
rebar or steel bolts. PRODUCT #713 exceeds the requirements of ASTM C
881-90 Types, I, II, Grade 3, Class A |
|
|
Product #714 Precast
Segmental Adhesive is a 100% solids, gelled epoxy
adhesive formulated to the requirements of ASTM C-881-90, Type VI, Grade
3, Class D, E, or F. AASHTO M-235-90 duplicates the technical
requirements of ASTM -C-881-90. |
|
|
Product #720 Cove Base Binder
- can be used to install an integral cove base for most
EpoxySystems' Flooring Systems, to provide seamless wall to floor
protection. |
|
|
Product #800 Water Based High Performance Sealer
Concentrate |
|
|
Product #801 Fast Set Acrylic Sealer |
|
|
810 Primer for Polyurea
is a two-component, clear, VOC compliant floor coating. PRODUCT #810 is
fast drying and will cure in temperatures as low as 35°F. Its convenient
2A:1B mixing ratio, no induction time and long pot life simplify mixing
and application. PRODUCT #810 protects by penetrating concrete or wood
and has excellent adhesion to damp concrete, it is an excellent concrete
primer. |
|
|
Product #824 Concrete Stain
and Coating
is a one component, water-repellant concrete stain. EPOXYSYSTEMS’
PRODUCT #824 penetrates existing concrete and imparts color and
uniformity the surface without affecting the natural texture. Standard
colors are white and gray many other colors of concrete are available.
- Special Order Product. Can be used only on certain projects. Minimum
quantities apply. Contact
Epoxy.com Tech Support for
details. |
|
|
Product #825 Epoxy Floor Sealer
is a non-rewettable, polymer emulsion formulated for use with
fast or normal setting floor underlayments. |
|
|
Product #826 Floor Curing Agent
- Minimum purchase of 10 each 55 gallon drums required. |
|
|
Product #830
is a two component modified epoxy system designed to seal concrete and
reduce moisture vapor transmission prior to applying finished flooring.
Epoxy.com Product #830 has proven to reduce moisture vapor emissions and
be resistant to damage from high alkalinity. Epoxy.com Product #830 is
an environmentally friendly material containing no hydrocarbons or other
solvents making |
