|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home

 

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980

 

Air Plane Hangers and Garages

Here are a list of the products most frequently used for Air Plane Hangers, and high end residential garage floors.

Solid Color

  • Product #1 All Purpose Coating - a 100% solids epoxy Hi-Build epoxy coating used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, etc Available in normal, fast, and Cold Temperature Cure versions. It has good chemical resistance, but should not be subjected to sunlight for extended periods of time. Most economical choice when only light chemical resistance is need, and there is little or no sunlight exposure.

  • Product #2 Chemical Resistant Coating - a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. Available in normal, fast, and Cold Temperature Cure. Has excellent chemical resistance, important if there will be a lot of fuel spillage, etc.  This product is the most commonly used product for hangers, because of its excellent chemical resistance, and economy.

  • Product #24 Pigmented Mortar - is a multipurpose colored epoxy binder for EpoxySystems’ Mortar Systems This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.  Best used when a thicker floor is needed to compensate for poor grade or finish on the concrete substrate.

  • Product #24 Fast Pigmented Mortar - Fast Cure

  • Product #24 Cold  Pigmented Mortar - Cold Temperature Cure

  •  Product #416 Polyurethane Coating  a moisture-cured, liquid applied, polyurethane, based on Aliphatic Isocyanides in combination with additives and pigments to produce a wear resistant, protective and decorative floor coating, for interior and exterior applications. It is primarily used as the protective topcoat of the  450 and 450X2  deck coating systems, but when used with the proper primer, can be used as a stand alone coating. Best when used when their will be little or not chemical exposure.  However, this material is nearly impervious to attach by sunlight.

  •  Product #458 2Component Urethane Coating - EPOXYSYSTEMS’ PRODUCT #458 is a liquid-applied, two-component, catalytic cured polyurethane floor and wall coating for use in air fields, industrial plants, stores, and other locations where surfaces must withstand heavy use of foot traffic. Best choice for light chemical exposure and lots of sunlight exposure.

  • Product #222 Water Based Epoxy - Epoxy Systems’ Product #222 WATER BASED EPOXY COATING is a two component 100% reactive water based multifunctional epoxy resin coating. Product #222 is manufactured to produce the utmost in performance in a safe, water borne coating. Product #222 provides excellent resistance to salt intrusion, and excellent adhesion to most common construction substrates.

Multi Colored

Clear Sealers

  • Product 850 (50% Solids - Penetrating Epoxy Sealer) - is a two-component penetrating epoxy sealer (with very high solids) designed for superior protection of new concrete or for prolonging the serviceability of partially-deteriorated concrete. The sealer is a low to medium viscosity material and is capable of providing an effective membrane barrier to inhibit moisture migration and corrosive chemical penetration. In the cured state ESItm Product #850 allows moisture vapor transmission; it seals off moisture entry but still allows the concrete to breath. When applied to concrete place and finished in accordance with standards defined in ACI 201 (Guide to Durable Concrete), Product #850 greatly improves wear resistance of the concrete surface, slows down the corrosion of reinforcing steel and adds many years' life to the structure. Product #850 has a solids content of 50% after curing. It may be applied to dry surfaces at temperatures of 40°F (0°C) or above. If you don’t need a pigmented system and you are looking for the best bang for the buck, this should be your choice.

  • Product #899 Epoxy Primer - a damp primer the is a 100% solids Low-Mod Low Viscosity Primer and Sealer. It may be used as a primer for any Epoxy Systems’ ™ product, or as a stand alone sealer. This is the best choice if you need a clear sealer, but cannot tolerate the solvents during installation of Product 850 (50% Solids - Penetrating Epoxy Sealer)

  • Product #223 Clear Water Based Epoxy Curing Compound, Sealer and Bonding Agent is a two component water based epoxy curing that is used to both cure and seal concrete and to bond freshly placed concrete to existing concrete. It is easily pigmented.

Hit Counter

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of
Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 375 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
 
www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253



Copyright © 1994-2008 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Technical Data Sheets in Adobe Acrobat Format][MSDSs in Adobe Acrobat Format][Online- Ordering Authorization Form]

Hit Counter

 

Secure Login