|
|
|
EpoxySystems' Product #889 Primer for Deck Coatings and Joint Sealers EpoxySystems’ Product #889 primer is a one component, moisture cured, primer for concrete and wood surfaces. Basic Uses: Used to promote adhesion of deck coating systems and joint sealants to concrete and wood. Color: Amber yellowish liquid. Sizes: 1 gallon cans, and 5 gallon pails. TECHNICAL DATA Consistency : Fluid Physical Appearance : Amber yellowish Odor : Aromatic Odor Dry Time : 2 hrs min. 8 hrs. max. at 77oF (25oC) and 50% R.H. Coverage Rate : 250 to 350 sq.ft. per gal. Shelf Life : 12 months when stored at 77oF (25oC) and 50% R.H. Weight Per Gallon : 8.60 lbs. (3.9 kg) Viscosity : 100 ± 50 cps
WARNINGS AND HAZARDS: Before using the products, always refer to MSDS for important warnings and safety information. Use only in areas with adequate ventilation. Avoid breathing vapors. Keep away from heat and flame. Avoid contact with eyes and skin. In the event of skin contact, remove immediately and wash with warm, soapy water. Wear suitable eye protection. Always wash hands before eating.
INSTALLATION All surfaces which are to be coated with EpoxySystems’ Product #889 must be free of contamination such as curing compounds, concrete hardeners, bond breakers, paint, etc. We recommend water-curing concrete instead of using concrete curing compounds. All surfaces must be clean, sound and dry. Sandblasting is recommended when possible, otherwise acid etching and wirebrushing may be sufficient. Coverage: 250 sq.ft. per gallon on rough surfaces. Up to 350 sq.ft. per gallon on smooth surfaces. All solvents must be allowed to evaporate off before application over EPOXYSYSTEMS’ PRODUCT #889 is possible. For best results, the surface that has been coated with EPOXYSYSTEMS’ PRODUCT #889 should be allowed to cure for a minimum of 2 hours before the application of the membrane or joint sealant. If for some reason the primer is allowed to cure in excess of 8 hours, the surface should be sanded and reprimed with EPOXYSYSTEMS’ PRODUCT #889. EPOXYSYSTEMS’ PRODUCT #889 should not be applied over wet surfaces as full adhesion and penetration will not be obtained. EPOXYSYSTEMS’ PRODUCT #889 may be applied by brush, roller or spray. Containers that have been opened must be used up within one or two days since it is a moisture-sensitive product. Clean Up: Because of the difficulty in cleaning up or removing cured EPOXYSYSTEMS’ PRODUCT #889, equipment and tools should be cleaned immediately after use with xylene or M.E.K. If cleaning operations are performed in areas where safety regulations do not allow the use of flammable solvents, 1,1,1, Trichloroethylene may be used. Use only water based hand cleaners for skin clean up. PRODUCT WARRANTY
Satisfactory results depend not only upon quality products but also upon factors beyond our control; methods of application and site conditions are examples of such factors and can affect product performance. This warranty consequently extends only to products installed in strict accordance with the manufacturer’s specifications. It is the users responsibility to satisfy himself, by his own information and tests, of the suitability of the product for his own intended use; user assumes all risk and liability resulting from his use of the product. The substrate to which the product is applied must be sound structurally and otherwise. Structural or substrate failures or imperfections resulting in damage to or failure of the product are not covered by this warranty. Since the use of the product is beyond the control of the manufacturer, the manufacturer assumes no liability for misapplication and misuse of the product. This warranty does not cover consequential damages, nor does it cover the labor attendant to replacing product in the event of a product failure. The warranty only extends to replacement of the product itself.
All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control, we cannot assume any risk or liability for results obtained, nor can we accept damages in excess of the purchase price of these products. TECHNICAL SERVICES All of the latest updates to product data and specifications are available at the EpoxySystems, Inc. website at www.epoxy.com. Since product data and specifications change, it is the users responsibility to make certain the most current versions of product data and specifications are being used.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
