|
|
|
EpoxySystems' Product #888 Epoxy Primer DESCRIPTION EpoxySystems’ Product #888 is a two-component, epoxy resin based concrete, metal, and wood primer for use with a wide variety of EpoxySystems’ Elastomeric systems. The primer may also be used with other polyurethane and epoxy systems, including joint sealants. Composition Modified Bisphenol A-Epichlorohydrin epoxy resin cured with an Amine hardener to set up to a durable tough film when used on wood, metal or concrete, including damp or green. Basic Uses Product #888 Primer is specially formulated as a primer for polyurethane coatings that are to be put down under conditions which would normally be considered adverse for application. On green concrete (concrete that is more than 8 days, but less than 28 days old), concrete floors poured in metal pans, or where the surrounding water table might cause a damp condition, Product #888 will set up to form a sound surface for polyurethanes and epoxies to bond to. Product #888 also has excellent adhesion to metal and wood surfaces. INSTALLATION All surfaces which are to be coated with Product #888 PRIMER must be free of contamination such as curing compounds, concrete hardeners, bond breakers, paint, etc. Water-curing concrete is recommended instead of using concrete curing compounds. All surfaces must be clean and sound, but may be damp. Sandblasting is recommended when possible, otherwise acid etching or wirebrushing may be sufficient.Coverage: 250 sq. ft. per gallon on rough surfaces. Up to 350 sq.ft. per gallon on smooth surfaces. For best results, the surface that has been coated with PRODUCT #888 should be coated over within 8 hours. If for some reason the primer is allowed to totally cure to a hard glass-like finish, the surface should be reprimed with another coat of PRODUCT #888before coating over with a polyurethane. However, if the surface is very porous, recoating of the primer may not be required. PRODUCT #888may be applied by brush, roller or spray. Clean Up: Because of the difficulty in cleaning up or removing cured Product #888, equipment and tools should be cleaned immediately after use, with xylene or M.E.K. If cleaning operations are performed in areas where safety regulations do not allow the use of flammable solvents, 1,1,1, Trichloroethylene may be used. Use only water-based hand cleaners for skin clean up. TECHNICAL DATA
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
