Epoxy.com Product #705100% Solids Flexible AdhesiveBest Adhesive for Bonding Plastics to Plastics or Plastics to Concrete, Steel, Wood and MasonryEpoxy.com Product #705 Two Component Flexible Adhesive has been replaced by Epoxy.com Product #701 Flexible BonderThis Material Data Sheet is for Reference only. Use Epoxy.com Product #701 instead. DESCRIPTIONEpoxy.com Product #705 Two Component Flexible Adhesive is a two component flexible adhesive, formulated to bond plastics to various substrates. Epoxy.com Product #705 Two Component Flexible Adhesive will adhere plastics to other plastics, concrete, steel, wood and masonry. Epoxy.com Product #705 Two Component Flexible Adhesive is thixotropic and is easily applied by serrated trowel. ADVANTAGES
SURFACE PREPARATIONFor best results, areas to receive the Epoxy.com Product #705 Two Component Flexible Adhesive should be free of laitance, grease, oil, and any other contaminants that would inhibit bond. Sandblasting, waterblasting, or wire brushing, or dust free grinding for surface preparation are recommended. MIXINGDouble Barrel Gun: With the use of static mixers in double barrel guns, no prior mixing of Epoxy.com Product #705 Two Component Flexible Adhesive is required. Special Order, minimum order required Hand Mixing: Small amounts of Epoxy.com Product #705 Two Component Flexible Adhesive can be mixed by hand using a strong stir stick. For large volume jobs to be mixed in 5 gallon pails or other suitable mixers where fillers such as Epoxy.com Product #75 Special Epoxy Aggregate or other oven dry silica sands are used, for best results combine two parts by volume of Component "A" with one part by volume of Component "B" of Epoxy.com Product #705 Two Component Flexible Adhesive in a clean pail, using a slow speed drill and an Epoxy.com Mixing Paddle. Mix for a minimum of three (3) minutes to a uniform consistency. To obtain a mortar, slowly add a maximum of one part by volume of Epoxy.com Product #75 Special Epoxy Aggregate while continuing to mix. COVERAGEWhen used neat, a 3 gallon unit of Epoxy.com Product #705 Two Component Flexible Adhesive will cover approximately 80 square feet (7.4 m²) at a 20 mil thickness. When used as a mortar, a 3 gallon unit of Epoxy.com Product #705 Two Component Flexible Adhesive, mixed with 3 gallons by volume of #75 Filler, will yield approximately 1,050 cubic inches of mortar. LIMITATIONSEpoxy.com Product #705 Two Component Flexible Adhesive should not be applied when surface temperatures are below 40° F (4.4° C). For best results, do not exceed one part by volume of Epoxy.com Product #75 Special Epoxy Aggregate to one part by volume of mixed Epoxy.com Product #705 Two Component Flexible Adhesive. CAUTIONWARNING! A Component contains epoxy resin. DANGER! B Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if it is heated or sprayed. Prevent all contact with skin and eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling. FIRST AID: In case of skin contact, immediately wash with soap and water. In case of eye contact, flush with copious amounts of water for at least 15 minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse. FOR INDUSTRIAL USE ONLY
| ||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
