Epoxy.com Product #703
100% Solids Semi-Flexible Epoxy Adhesive
Epoxy Bonder | Epoxy Bonding Adhesive
DESCRIPTION
Epoxy.com Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder
is a 100% solids, moisture insensitive epoxy resin system, containing no
solvents. When mixed at a 2:1 ratio by volume, it produces a non-sagging
material that is ideal for repairs on vertical or overhead surfaces. Product
#703 Semi-Flexible Epoxy Gel Adhesive exceeds the requirements of ASTM C
881-87, Types I, II, and III Grade 3, Class "B", "C", "E" and "F". Epoxy.com
Epoxy Gel Adhesive has Zero (0) VOC. Since it has no VOC it makes it safer to
use, and meets even the strictest low VOC requirements
USES
Repair and Assembly of Stone Monuments
Stone Counter Top Bonding
Cemetery Monument Repair.
Sealing Joints in Plywood Substrates to Receive Epoxy.com Seamless
Flooring Systems
Bonding Dissimilar Materials with Slightly Different Coefficient of
Expansion
Patching
General Purpose Bonding where a Semi-Flexible Adhesive is Required
ADVANTAGES
- Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder
will bond to damp or dry surfaces.
- Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder
may be feather-edged and will not shrink.
- Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder
is readily dispensed into narrow slots and holes from cartridge dispensers, or
concrete grout bags
- Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder
has excellent resistance to gasoline, oil, sewage and aggressive water.
- Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder is
100% solids Epoxy
- Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder has
Zero (0) VOC
- Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder meets
ASTM C 881-87, Types I, II, and III Grade 3, Class "B", "C", "E" and "F"
PHYSICAL PROPERTIES
| Gel Time @ 72° F (22.2° C) |
30 minutes minimum |
Physical |
Tensile Strength @ 72° F (22.2° C)
(ASTM D 638) |
5,000 psi minimum (34.5 MPa) |
Linear Coefficient of Shrinkage on cure
(ASTM D 2566) |
0.005 |
Compressive Strength
(ASTM C 109 Modified) |
11,000 + psi minimum (75.8 MPa) |
Compressive Modulus
(ASTM D 695) |
200,000 + (1379 MPa) |
| Bond Strength (Slant Shear)
(ASTM C 882-78) |
7 days
2 day moist cure
14 day moist cure |
3,000 psi minimum (20.7 MPa)
1,000 psi + (6.9 MPa)
1,500 psi + (10.3 MPa) |
Electrical |
| Dielectric Strength, S/T |
Volt per mil 440-465 |
| Dielectric Constant |
60 HZ 3.4 - 3.5
106 HZ 3.3 - 3.4 |
| Power Factor |
60 HZ 0.006 - 0.007
106HZ 0.03 - 0.04 |
Installation
SURFACE PREPARATION
For best results, areas to receive the Product #703 Semi-Flexible
Epoxy Gel Adhesive Bonder should be free of laitance, grease, oil, and
any other contaminants that would inhibit bond. Sandblasting, waterblasting, or
wire brushing, or dust free grinding for surface preparation are recommended.
See Epoxy.com Surface Preparation Guide.
MIXING
Double Barrel Gun: With the use of static mixers in double
barrel guns, no prior mixing is required.
Mixing: For large volume jobs to be mixed in 5 gallon pails
or other suitable mixers where fillers such as Product #75 or other oven dry
silica sands are used, for best results combine two parts by volume of Component
"A" with one part by volume of Component "B" of Product #703
Semi-Flexible Epoxy Gel Adhesive Bonder in a clean pail, using a slow
speed drill and an Epoxy.com Mixing Paddle. Mix for a minimum of three
(3) minutes to a uniform consistency. To obtain a mortar, slowly add a maximum
of one part by volume of Product #75 Filler while continuing to mix.
COVERAGE
When used neat, a 3 gallon unit of Product #703 Semi-Flexible Epoxy
Gel Adhesive Bonder will cover approximately 80 square feet at
a 20 mil thickness. You can also consultt he Epoxy.com
Neat (unfilled) Resin Calculator. When used as a mortar, a 3 gallon unit
of Product #703, mixed with 3 gallons by volume of #75 Filler,
will yield approximately 1,050 cubic inches of mortar. If using this as an
anchor bolt, or dowel bar adhesive, you can double check you volume with the
Epoxy.com Dowel Bar and Anchor Bolt
Adhesive Calculator.
LIMITATIONS
Product #703 Semi-Flexible Epoxy Gel Adhesive Bonder should
not be applied when surface temperatures are below 40° F (4.4° C). For best
results, do not exceed one part by volume of #75 Filler
to one part by volume of mixed Product #703 Semi-Flexible Epoxy Gel
Adhesive Bonder .
CAUTION: WARNING!
A Component contains epoxy resin. DANGER! B Component contains
alkaline amines; strong sensitizer. May cause skin sensitization or other
allergic responses. Use with good ventilation, particularly if it is heated or
sprayed. Prevent all contact with skin and eyes. Wear protective clothing,
goggles, gloves and/or barrier creams. Keep container closed when not in use.
Wash thoroughly after handling.
FIRST AID: In case of skin contact, immediately wash with soap and
water. In case of eye contact, flush with copious amounts of water for at least
15 minutes. Remove contaminated clothing and shoes. If irritation persists, seek
medical attention. Wash clothing before reuse.
FOR
INDUSTRIAL USE ONLY / KEEP AWAY FROM CHILDREN
