|
|
|
EPOXYSYSTEM’ PRODUCT #451 AROMATIC POLYURETHANE COATING
EPOXYSYSTEMS PRODUCT #451 is an aromatic, liquid applied, single-component, moisture cured polyurethane floor coating for use in indoor applications such as industrial plants, mechanical rooms, and locations where surfaces must withstand pedestrian traffic.PRODUCT DESCRIPTION Composition: A single component, aromatic based , moisture-cured polyurethane coating.Basic Uses: EPOXYSYSTEMS PRODUCT #451 is primarily used as a protective top coat of the ELASTO-DECK 5000 M.R. deck coating system. It may also be used as a durable finish that protects interior floors against occasional chemical spillage, dirt, grease and oils. EPOXYSYSTEMS PRODUCT #451 gives floors a well maintained look while retaining a glossy appearance. Dusting of concrete floors is minimized when the surface is sealed with EPOXYSYSTEMS PRODUCT #451. EPOXYSYSTEMS PRODUCT #451 is intended for interior applications only. Coating will discolor if exposed to sunlight. Limitations: Containers that have been opened must be used up within one or two days since it is a moisture-reactive material. It sets up when exposed to air. Colors: Concrete Grey, Tan Sizes: Available in 1 gallon cans, 5 gallon pails and 55 gallon drums .INSTALLATION Surface Preparation: EPOXYSYSTEMS PRODUCT #451 may only be applied to dry, clean surfaces. It is recommended to prepare concrete floors by acid-etching or sandblasting. EpoxySystems Product #889 Concrete Primer or EpoxySystems Product #888 Epoxy Concrete Primer may be required prior to applying EPOXYSYSTEMS PRODUCT #451 depending on the concrete substrates condition. All oxidation and rust must be removed from metal surfaces and all metal must be primed with EpoxySystems’ Product #887 Metal Primer.Application: EPOXYSYSTEMS PRODUCT #451 may be applied by all conventional means, including spray equipment, paint rollers, and brushes. The rate of application is typically 125 sq. ft. per gallon (3.06 m2/liter). Additional coats may be applied after an overnight cure. It is important not to wait for more than 24 hours before recoating if additional coats are desired. Allow a final cure time of 48 hours before the coating is exposed to traffic. Caution: An appropriate aggregate, such as aluminum oxide, monterey sand, or other suitable anti-skid material, must be added to the final or next to last coat, in sufficient size and quantity to prevent the coating from being slippery.PRODUCT WARRANTY All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control we cannot accept damages in excess of the purchase price of these products.MAINTENANCE If EPOXYSYSTEMS PRODUCT #451 is damaged, it can be repaired by cleaning the surface with M.E.K. and recoating it with EPOXYSYSTEMS PRODUCT #451 system.
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
