|
Epoxy.com Product #304 Epoxy is a moisture insensitive,
two-component, 100% solids epoxy resin system designed specifically for use in
temperatures of 40°F and below.
Epoxy.com Product #305 & #306 Epoxy Injection Resins For Reference Only - Replace By Epoxy.com Product #303 Epoxy.com Products #305 and Product #306 are two-component, low viscosity, 100% solids epoxy resin base adhesive. Modified Bisphenol A-Epichlorohydrin epoxy resin and Amido-amine type hardener, modified to be compatible with damp concrete. Product #305 has a Potlife of 1 hour at 77 ° F (25° C) Product #306 is a fast version of Product #305. Product #306 has a pot life of 5-10 minutes at 77° F (25° C)PRODUCT #305 AND PRODUCT #306 is used to restore cracked structural or non-structural concrete to acceptable strength standards by the introduction of an epoxy resin compound, through injection under pressure by either hand operated guns or powered mixing-pump equipment. PRODUCT #305 AND PRODUCT #306 have the ability to penetrate into hairline cracks, due to its low viscosity. Color: Clear Sizes: Packaged in 1 1/2 gallon kits and 15 gallon kits. Standards: CALTRANS 8040-01F-02 INSTALLATION All cracks must be adequately covered on the surface with Epoxy.com Product #6 epoxy paste, and pressure injection ports imbedded in the paste in the holes drilled directly over the center of the crack at distances dictated by the thickness of the concrete structure, severity of cracks and other job factors. The injection adhesive is introduced at the first valve under sufficient pressure for the epoxy compound to advance to the adjacent valve. The first valve is then capped and the introduction of the epoxy is shifted to the valve at which the epoxy compound appears. The procedure is repeated until the entire crack has been sealed. After a 24 hour cure, the valves and epoxy paste are removed by grinding them flush with the surface. Product #305 is recommended for sealing cracks in large structures, where the epoxy must flow for a long period of time before the crack is penetrated and filled. Product #306 is most suitable for relatively thin structures, or where there is danger of the epoxy compound flowing out of the cracks before it hardens. For more information about epoxy injection please contact Epoxy.com Technical support department, and/or visit www.epoxy.com/injection.htm. PRODUCT WARRANTY All products proven to be defective in manufacturing will be replaced at no charge. Since the use of these products is beyond our control we cannot assume any risk or liability for results obtained, nor can we accept damages in excess of the purchase price of these products. MAINTENANCE If additional cracks develop in the structure it is unlikely to be caused by the failure of the epoxy resin due to its great adhesive strength, but rather newly developed cracks in the concrete. New cracks are treated the same way as described above. TECHNICAL DATA FOR PRODUCT #305 AND PRODUCT #306
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all
Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
