Epoxy.com Product #260

Corrosion Resistant Epoxy Protective Primer/Coating


 

DESCRIPTION:

Epoxy.com PRODUCT #260 Corrosion Resistant Epoxy Protective Primer and Coating are two-component, 100% solids epoxy coatings based on multi-functional high performance resin and anti-corrosive pigment. PRODUCT #260 is used as a two coat system. PRODUCT #260 provides corrosion resistant protection to steel and other metals. PRODUCT #260 has excellent resistance to chemicals up to 300F, and hot water resistance at temperatures up to 250F under continuous immersion. Epoxy.com PRODUCT #260 is formulated in a convenient 2 to 1 ratio, by volume mix ratio and has a long pot life to simplify application. The primer is green and the topcoat is blue. (Other colors are available as special order product.) PRODUCT #260 is particularly effective in applications which entail force curing, either as pre-immersion or during immersion service.

 

ADVANTAGES:

bulletExcellent corrosion barrier properties.
bulletExcellent chemical resistance.
bulletExcellent adhesion to most metals.
bulletExcellent thermal resistance.
bulletTough, tile-like finish.
bulletProtects concrete, steel, or wood against attack by salts, acids, and alkalies.
bulletHigh non-sag properties can be applied up to 30 mils in 1 coat.

 

WHERE TO USE:

For Chemical Protection of:

bulletSteel Tanks
bulletPiping
bulletHeat Exchangers
bulletCondenser Boxes
bulletHot Water Tanks
bulletConcrete
bulletManholes

 

PHYSICAL PROPERTIES:

Tensile Strength
   ASTM D-638
8000 psi
Tensile Elongation 2-4 %
Compressive Strength
   ASTM D-695
12000 PSI
Pull Off
   ASTM D-1002
 
Mix Ratio 2:1 by volume
Gel Time, 100 grams 60 Minutes
Pot Life 40 minutes at 75F

Cured Film -

Abrasion Resistance
   ASTM D-968
Excellent
Solvent Resistance Good
Alkali Resistance Excellent
Acid Resistance Good

For your specific chemical problem, consult Epoxy.com directly.

 

SURFACE PREPARATION:

Steel Surfaces: Steel surfaces should be abrasive blasted to a commercial gray metal finish as specified by the Steel Structures Painting Council SP-6. For immersion service, blast to near white blast SSPC SP-10.

 

MIXING:

Stir Components "A" & "B" thoroughly before mixing. Combine two parts by volume of "A" with one part by volume of "B" (mixing ratio 2:1). Mix for not less than three minutes using a slow speed drill (300 to 600 rpm) and Epoxy.com -Mixing Paddle. Scrape side and bottom to ensure through mixing. Avoid entrapping air. Apply immediately after mixing.

 

APPLICATION:

Epoxy.com PRODUCT #260 Corrosion Resistant Epoxy Protective Primer and Coating may be applied by brush, roller, or spray. All spray equipment must employ traps to prevent water and oil from contaminating coating. Thinning may be required for brushing and rolling. Heating may be required for spraying. Heating will shorten pot life to 20 minutes at 100F. Apply immediately after mixing. Apply 10 mils wet film thickness. Apply topcoat after primer is tack free between 4 and 24 hours. If heated, the tack free time will be reduced.

 

COVERAGE:

Apply Epoxy.com Epoxy.com Product #260 Corrosion Resistant Epoxy Protective Primer and Coating at a rate of100-200 square feet per gallon (per coat), dependent upon surface texture and desired thickness.

 

SHELF LIFE:

2 years

 

PACKAGING:

PRODUCT #260 Corrosion Resistant Epoxy Protective Primer and Coating is packaged in 3-gallon and 15-gallon kits.

CAUTION:

WARNING! "A" Component contains epoxy resin. DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with eyes or skin. Wear protective clothing, goggles, gloves, and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.

FIRST AID:

In case of skin contact, immediately wash with soap and water. In case of eye contact, flush with copious amounts of water for at least 15 minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN