|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|
EpoxySystems' Product #215
DESCRIPTION Product #215 is a high solids, epoxy-polyamide combination, chemical curing, quick- drying resin system. Product #215 produces a ceramic like coating on masonry, concrete plaster, cement, asbestos board, wood, fiberglass, metal and most other rigid materials. Formulated for applications that require superior adhesion and durability, chemical resistance, corrosive protection, quick cure and easy cleaning. Product #215 can be used as a primer where corrosion resistance or fast cure is required. Product #215 can be used as a sealer for porous surfaces such as troweled, poured, or precast concrete. Drying time is consistent, however, chemical curing is dependent upon temperature and ventilation. ADVANTAGES
APPLICATION PROCEDURES SURFACE PREPARATION Before applying Product #215 surface must be clean and sound. Remove all dirt, laitance, grease, curing compounds and other foreign matter by sandblasting, mechanical abrasion, or acid etching. Remove water and dust from all surfaces with an oil-free air blast immediately prior to application. MIXING INSTRUCTIONS Temperature of Product #215 must be 50° F or above at time of mixing. Stir each component separately before blending. Mix equal volumes of Part A and Part B for three minutes with a low speed drill motor equipped with a mixing paddle. APPLICATION To apply Product #215 use a brush, roller, or spraying (conventional) equipment. Induction time is one hour at 65-95° F, two hours at 55-65° F or when humidity is 60-85%. Second coat can be applied three hours after initial application.
LIMITATIONS Temperature of substrate must be above 50° F. DO NOT apply over wet surface
SAFETY PRECAUTIONS Prolonged or repeated exposure may cause eye or skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber or polyethylene gloves.
CLEANING All tools and equipment should be cleaned before the system gels. Use toluene, MEK or any lacquer solvent.
SPECIFICATIONS
This information is presented in good faith to assist in determining
whether this product is suitable for application. No warranty or representation, however,
is intended or made, nor is protection from any law or patent to be inferred, and all
patent rights reserved. 9507 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
|
